I need a Spyder KEY ... without the CHIP !!!

[BLUEKNIGHT911]

I was lucky enough to have my DESS module Canceled / silenced ….. So I don't need a chipped key, and would rather not pay $ 25.00 ++++ for a genuine OEM key. Soooooooooooo, who has bought one ( Non-chipped ) what brand is it ???... where did you get it ??? … how much did you pay ….. Thanks … Mike :ohyea:…...Did some searching and learned that this key could be an Ilco X270….. :thumbup:Can anyone verify this ????? thanks , Mike

[bigbadbrucie]

Mike, I just went to a local locksmith and he looked at my key, went to his carousel of keys, chose one and cut it. I still have DESS enabled, hut it locks and unlocks everything. It’s an Ilco 270x

[JayBros]

Mike, I bought an Ilco X270 when I first got my Spyder. I found that I had to bevel the key as shown in the picture so I could push it far enough into the ignition switch to unlock the frunk and seat.

175328

[springcrawler]

Mike when i had my my dess undone i went to my local ACE hardware store they used a old Triumph blank #TMP1 COST =$1.75 HAD 3 MADE LOL
Good luck

[Haze]

Mike, I bought an Ilco X270 when I first got my Spyder. I found that I had to bevel the key as shown in the picture so I could push it far enough into the ignition switch to unlock the frunk and seat.

175328

I carry an ILCO X270 key in my wallet. Its cut to fit my 2013 ST. Had to bevel the key to fit deep enough into the bezel.
Cheers, David C.

[BLUEKNIGHT911]

Spyder key blank - Thanks to all who responded ….. I found the Ilco X270 on E-bay for $ 3.32 each … for two ,.. and seller will combine shipping , soooooo $10.00 for two delivered …. I will check my local ACE hardware, because if you buy their blank cutting it is included :2thumbs:...… Mike :ohyea:

[JayBros]

I had to hunt for a hardware store that had the Ilco blank; it was the hardest part for me. Big boxes and local hardware didn't have, no Ace nearby.

[Navydad]

My local ACE Hardware store had Can Am blanks in stock. They look like the Spyder keys, but aren't chipped. I had two cut and have $10 in them. They work everything except the ignition, but after next week they will work the ignition as well :yes:

[wmh9680]

I was lucky enough to have my DESS module Canceled / silenced ….. So I don't need a chipped key, and would rather not pay $ 25.00 ++++ for a genuine OEM key. Soooooooooooo, who has bought one ( Non-chipped ) what brand is it ???... where did you get it ??? … how much did you pay ….. Thanks … Mike :ohyea:…...Did some searching and learned that this key could be an Ilco X270….. :thumbup:Can anyone verify this ????? thanks , Mike

That's what I used. How did you have tour DESS cancelled and what all does that do?

[BLUEKNIGHT911]

My local ACE Hardware store had Can Am blanks in stock. They look like the Spyder keys, but aren't chipped. I had two cut and have $10 in them. They work everything except the ignition, but after next week they will work the ignition as well :yes:

So am I think ….. the key slides in - But won't start the Spyder because of the DESS module ( ie no chip in that key ) ???? ………..thanks - Mike :ohyea:

[jcthorne]

I was lucky enough to have my DESS module Canceled / silenced ….. So I don't need a chipped key, and would rather not pay $ 25.00 ++++ for a genuine OEM key. Soooooooooooo, who has bought one ( Non-chipped ) what brand is it ???... where did you get it ??? … how much did you pay ….. Thanks … Mike :ohyea:…...Did some searching and learned that this key could be an Ilco X270….. :thumbup:Can anyone verify this ????? thanks , Mike

I can verify the Ilco X270 is the right key. Works in all Spyders. I keep one in my billfold.

[Navydad]

So am I think ….. the key slides in - But won't start the Spyder because of the DESS module ( ie no chip in that key ) ???? ………..thanks - Mike :ohyea:

Correct.

[troop]

Couldn't they have designed the OEM key to have a hole for a key ring??

[BLUEKNIGHT911]

Correct.

:thumbup::thumbup:...…………..Mike :ohyea:

[eddieshep999]

Couldn't they have designed the OEM key to have a hole for a key ring??

See:-

https://www.spyderlovers.com/forums/showthread.php?92387-key-ring-hole&highlight=ring

[troop]

See:-

https://www.spyderlovers.com/forums/showthread.php?92387-key-ring-hole&highlight=ring

Awesome !! Thank you

[wmh9680]

I made the mistake once of putting the nonchipped key in the ignition to open the funk and it took me 45 min to get it out

[billybovine]

Order some from China. https://www.aliexpress.com/item/32963274857.html?spm=a2g0o.productlist.0.0.7dff53f 6ThyLhK&algo_pvid=72121b83-7775-40ad-bf57-d73f2dc205d0&algo_expid=72121b83-7775-40ad-bf57-d73f2dc205d0-0&btsid=83365915-7d30-4546-8b1b-ff80a2efd201&ws_ab_test=searchweb0_0,searchweb201602_6,searchwe b201603_53

[JayBros]

I made the mistake once of putting the nonchipped key in the ignition to open the funk and it took me 45 min to get it out

Was it an Iclco X270? Had you beveled it first?

I tested my Ilco in the trunk and it worked fine. When I tried it in the ignition it was an obvious no-go, couldn't depress it at all so I used a chipped key to determine the angle and amount of bevel and allowed a little more grinding for insurance.

[BLUEKNIGHT911]

Order some from China. https://www.aliexpress.com/item/32963274857.html?spm=a2g0o.productlist.0.0.7dff53f 6ThyLhK&algo_pvid=72121b83-7775-40ad-bf57-d73f2dc205d0&algo_expid=72121b83-7775-40ad-bf57-d73f2dc205d0-0&btsid=83365915-7d30-4546-8b1b-ff80a2efd201&ws_ab_test=searchweb0_0,searchweb201602_6,searchwe b201603_53

wow ... that price is fantastic , per chance have you bought these for yourself, and did they / it work ...... Thanks for this find .... Mike :ohyea:

[Trbayth]

wow ... that price is fantastic , per chance have you bought these for yourself, and did they / it work ...... Thanks for this find .... Mike :ohyea:

It's interesting that that listing says "It allows you to put the chip of your original key in this key blank". I'm going to chalk that one up to a bad translation but if they have figured out how to allow a chip transplant, that's interesting.

Like you, I finally had enough of DESS problems.

[billybovine]

wow ... that price is fantastic , per chance have you bought these for yourself, and did they / it work ...... Thanks for this find .... Mike :ohyea:

Nope, never bought any. Never seen the need so far. Just remembered seeing them a while back.

[BLUEKNIGHT911]

Nope, never bought any. Never seen the need so far. Just remembered seeing them a while back.

Thanks Billy …. from the pics of the Key it looks exactly like my OEM key …. so I'll order some and let you know ….. Mike :ohyea:

[trikermutha]

Thanks Billy …. from the pics of the Key it looks exactly like my OEM key …. so I'll order some and let you know ….. Mike :ohyea:

Should get them in Oct sometime per the web site

[BLUEKNIGHT911]

Should get them in Oct sometime per the web site

So far 5 attempts and no luck …. very difficult web site to navigate …… Mike :ohyea:

[billybovine]

When I have bought stuff through aliexpress. It takes 50 to 60 days to get. Your experience in the US may be different.

[IdahoMtnSpyder]

I made the mistake once of putting the nonchipped key in the ignition to open the funk and it took me 45 min to get it out
Obviously it wasn't cut correctly!

[wmh9680]

Just to top it off it was Friday afternoon starting the holiday weekend so there was no getting help and 40 miles from home in a Walmart parking lot in Bradley Illinois.