heated grips?

[Rogue Hawk]

They are not an option right now. I wonder if there is a third party brand I can use. Maybe Oxford? BTW, I hated the ones on the F3, they never got hot enough and the button was so tiny I could not toggle it with a gloved hand.

[Tslepebull]

I hope to see something in the aftermarket. Heated grips are so cozy

[Spider-man]

I got these. Pretty easy to install, and they get hot as he**!

https://www.amazon.com/gp/product/B000R566SI/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

[Sarge707]

I researched the Oxford "Premium " Updated grips and was going to put them on the Ryker but decided just to get another battery harness and use my Warm and Safe Glove liners that I use on the F3. The liners are so much more comfortable than gripping to feel heat. Minus feature-you attach the wire?

[BLUEKNIGHT911]

I can't comment on the Oxford brand …… but I have seen many others - that have multi- heat levels, check what's available on E-bay …… Mike :thumbup:

[Rogue Hawk]

I do want one where I can change the temperature. Are the Ryker bars the same size as on two wheelers?

[Triumphcycleman]

YEP, 1 7/8"

[canamjhb]

I don't remember the brand but we had heated grips installed on my wife's Goldwing that had a rotating reastat. She had infinate control over heat output. I do remember they were made by a common motorcycle aftermarket company so should not be too hard to find...... Jim

[Sarge707]

https://youtu.be/aX4mV8XyPI8

These are well rated and have 5 Percentage settings on the controller. Won't break the bank either-

[RNBOB]

They are not an option right now. I wonder if there is a third party brand I can use. Maybe Oxford? BTW, I hated the ones on the F3, they never got hot enough and the button was so tiny I could not toggle it with a gloved hand.

I installed oxford on my Honda Nc700x. It was easy and has 5 levels of heat. Warmer then the ones on my F3L.
Bob

[Rogue Hawk]

YEP, 1 7/8"

Good, the F3 has big chunky none standard bars. So on the Ryker, I should be able to install a 'standard' kit meant for a transitional bike. The only other concern I have is the bar end mirrors. I don't know if they can be reattached to the third party grips. I may have to get some 'rabbit ears' rear view mirrors. Thoughts?

[Markubis]

Has the smaller battery size on the Ryker been considered when looking at heated grips? Or will it come into play...since the heated grips will require a certain amount of amperage to run ?

[Sarge707]

Good, the F3 has big chunky none standard bars. So on the Ryker, I should be able to install a 'standard' kit meant for a transitional bike. The only other concern I have is the bar end mirrors. I don't know if they can be reattached to the third party grips. I may have to get some 'rabbit ears' rear view mirrors. Thoughts?

https://youtu.be/4MNBKrWMSSQ

This shows the end bars loosening- Not sure if the grips would work or Not. BRP does sell the Sport Grips so you must be able to change them?

[Rogue Hawk]

https://youtu.be/4MNBKrWMSSQ

This shows the end bars loosening- Not sure if the grips would work or Not. BRP does sell the Sport Grips so you must be able to change them?

I guess I will have to wait and see. The bunny ears is always an option since the ryker has a normal sized bar.

Here is one that fits the 1 7/8 bar. I may try this.

https://www.revzilla.com/motorcycle/oxford-heaterz-premium-adventure-heated-grips

[old Timer]

Has nothing to do with Battery Size, but everything to do with Alternator out put and system power draw. Doubt if heated grips would be the slightest problem at all.

[cueman]

I agree with old timer as I have a heated jacket liner and heated gloves. :cheers: cueman