Can Am armrests

[lewisalice]

My new armrests Installed 157617157617and looking good

[MikeT]

Did you install them, or had them installed????

[slick999]

look great,were they hard to install

[DGoebel]

How Solid are the mounts, Can you push down on the front end of the armrests without them flexing or breaking loose?

[Zip]

Did you make them or buy them?

[Bob Denman]

Those are the passenger armrests offered by BRP...

157621157621

[lewisalice]

Did you install them, or had them installed????

Dealer

[Merlot2015]

I installed mine 3 weeks ago... the install was a pretty basic job just requiring the rear body panel, passenger backrest and armrest/speaker side panels be removed. The only part that is replaced is the soft cushion part on top of the armrest/speaker panel. If you have a stock passenger backrest it's a real simple job...but if you have a custom seat, I have an Ultimate, it may require some additional work so that the seat lines up flush with the back wall of the trunk. (otherwise there will be a 1/4" to 1/2" gap)

Excellent build quality with little to no flex when pressing down on the front of the armrests. Both armrests flip-up and can remain in either the up or down position while on the road.
The wife loves them :clap: think the added cushion that the Ultimate seat provides raises her up high enough to not poise a height problem for her.

[Little Blue]

LIKE IT. Well done :thumbup:

[bcer960]

I installed mine 3 weeks ago... the install was a pretty basic job just requiring the rear body panel, passenger backrest and armrest/speaker side panels be removed. The only part that is replaced is the soft cushion part on top of the armrest/speaker panel. If you have a stock passenger backrest it's a real simple job...but if you have a custom seat, I have an Ultimate, it may require some additional work so that the seat lines up flush with the back wall of the trunk. (otherwise there will be a 1/4" to 1/2" gap)

Excellent build quality with little to no flex when pressing down on the from of the armrests. Both armrests flip-up and can remain in either the up or down position while on the road.
The wife loves them :clap: think the added cushion that the Ultimate seat provides raises her up high enough to not poise a height problem for her.


Thanks for the review.

[Ryder_Robert]

Those were the ones I wanted a year ago but according to the dealer were only available on the F3.

[Bob Denman]

Well: They're available now... :D :thumbup:

[Zip]

Anyone know the cost?

[bcer960]

Anyone know the cost?

I just paid $400 cdn ( Im in B.C.) plus taxes for my set. I have not put them on, as the bike is put away for the winter.

[Merlot2015]

Anyone know the cost?

$349 part #219400839

pg 78
http://www.publications.brp.com/brp-can-am-spyder/2018-spyder-my18-pac-catalog-ca-us/

[Zip]

$349 part #219400839

pg 78
http://www.publications.brp.com/brp-can-am-spyder/2018-spyder-my18-pac-catalog-ca-us/

Thank you

[lewisalice]

Thank you
I got 15% off that price

[Merlot2015]

Congrats on the armrests! Out of curiosity, what dealer did the install and what did they charge you?

[11rtLTD]

I got 15% off that price

Got a coupon code to Share??

[lewisalice]

Got a coupon code to Share??
There was no coupon code it was the dealer just giving me a discount

[Reedlabs]

I installed mine 3 weeks ago... the install was a pretty basic job just requiring the rear body panel, passenger backrest and armrest/speaker side panels be removed. The only part that is replaced is the soft cushion part on top of the armrest/speaker panel. If you have a stock passenger backrest it's a real simple job...but if you have a custom seat, I have an Ultimate, it may require some additional work so that the seat lines up flush with the back wall of the trunk. (otherwise there will be a 1/4" to 1/2" gap)

Excellent build quality with little to no flex when pressing down on the front of the armrests. Both armrests flip-up and can remain in either the up or down position while on the road.
The wife loves them :clap: think the added cushion that the Ultimate seat provides raises her up high enough to not poise a height problem for her.

Hoping you can help here. I just got my new ultimate seat and passenger backrest today but the passenger backrest is not fitting - as I also have the BRP armrests. What did you have to do to get this combination to work. I've fiddled for the last couple of hours to no avail.

Thanks!

Reed

[Merlot2015]

Hi Reed, I think I can help...this is what I did to eliminate the gap.
#1 - I used a hot knife to reduce the width of the anchor by approx 1/2”.
#2 - I cut away the excess seat molding material and shaped it to fit snugly into the anchor assembly.

I’ve attached the before and after pics.

Hope this helps!

[safecracker]

Installed my armrests Wensday and wife likes.them.so far. I went for a short ride yesterday and twice the armrests would flip up when going 70 MPh. Not a big deal. Armrests are fairly straight forward to install.

[mark4Jesus]

Installed my armrests Wensday and wife likes.them.so far. I went for a short ride yesterday and twice the armrests would flip up when going 70 MPh. Not a big deal. Armrests are fairly straight forward to install.

How long did it take to install?

[safecracker]

I took my time, about 1.5 hrs. My swollen ankle kept me in check. You will notice there are 2 different bolt lengths. Installation instructions could.have better pics, but the install is pretty straightforward. Good luck. Bruce

[Reedlabs]

Hi Reed, I think I can help...this is what I did to eliminate the gap.
#1 - I used a hot knife to reduce the width of the anchor by approx 1/2”.
#2 - I cut away the excess seat molding material and shaped it to fit snugly into the anchor assembly.

I’ve attached the before and after pics.

Hope this helps!

This is perfect! I was wondering if those little guys were the issue but since i had my armrests installed the day i got the bike, i didn't know for sure if they were stock or part of the armrest piece. This answers it clearly. I've also reached out to Ultimate to see what they have to say but I know this answer is right and my query to them will probably just let them know there's an issue for BRP armrests.

Thanks again!

Reed

[DGoebel]

Many thanks to all who did this already and posted their experience, I ordered and today installed these and gotta say, the hardest part for me was the @#$@#%^ Antenna.
She who must be obeyed has already tried and approved the feel and comfort. Looking forward to a Mother's day long ride.
Whilst checking them out I think I did see where the hinge of the flip up portion could be tightened up if you wanted to.
I really liked the integrated support that slipped behind the backrest.

[Fire34]

The wife loves them we had the dealer install them though, but they look like they great. Just wish I could get the wife to get her license so i can fall a sleep back there:sour: at the same time we had the custom dynamics third brake light installed and it looks great also. I am so afraid to tear into things afraid I will do more harm than good. But we or should I say she loves them.
Dave

[3 Wheel Rider]

Rode to the dealer yesterday to see if they had the armrests in stock and to my surprise they did. The armrests felt pretty solid. I paid for a pair and scheduled an install for next Thursday. :yes:

[Ezrider]

Hi Reed, I think I can help...this is what I did to eliminate the gap.
#1 - I used a hot knife to reduce the width of the anchor by approx 1/2”.
#2 - I cut away the excess seat molding material and shaped it to fit snugly into the anchor assembly.

I’ve attached the before and after pics.

Hope this helps!

Great advice and great pics! could not have made it work without you post!

[Merlot2015]

Happy that I could help out...enjoy your new armrests!