Anyone know how to remedy Hyperflash?

[SteveandBelinda]

Had some LED's put on couple weeks ago. Have fender lights hooked to turn signal. When I put on turn signal, it flashes normal about 2 times, then hyper flashes. I tried doing what Lamont does on his video about hyper flash, but it does nothing for me. It's on a 2014 RTL

[spyderfever]

Some people have had the same problem and were told to have the engine running when you do it. It may be worth a try! Good luck!

[Centurion]

We also have a 2014 RTL and Lamont's instructions to correct the hyper flash worked for our bike as written in the Spyderpops kit.

[Bob Denman]

...They worked just fine on my 2014 RT-L also.
But you do have to make sure that you follow the instructions EXACTLY s he laid them out...

https://youtu.be/gpuEqpiTm4M

[MisterP]

TricLED told me to hold the emergency flasher button for 30 seconds with the engine running, because the reset is sensitive to voltage. That's worked for me.

[Blue Star]

Will hyper flash do any damage to the electrical system? I'm in the process of putting on LED lighting, and have it. I kind of like it, but not sure if it will damage the system.

[PapaHotel]

I had the hyper flash for my entire trip home from Spoyderfest. The bike was very wet from the torrential monsoon we rode home in. Once the bike dried out the hyper flash went away.

[PapaHotel]

I had the hyper flash for my entire trip home from Spyderfest. The bike was very wet from the torrential monsoon we rode home in. Once the bike dried out the hyper flash went away.

[SteveandBelinda]

[Followed them to the letter, about half a dozen times.

QUOTE=Bob Denman;1263464] ...They worked just fine on my 2014 RT-L also.
But you do have to make sure that you follow the instructions EXACTLY s he laid them out...

https://youtu.be/gpuEqpiTm4M[/QUOTE]

[SteveandBelinda]

Tried that too. Does not work either.

TricLED told me to hold the emergency flasher button for 30 seconds with the engine running, because the reset is sensitive to voltage. That's worked for me.

[Centurion]

I would try calling the vendor from who you purchased the items. Both Spyderpops and Tricleds have awesome customer service! Their staff really know their products and probably talk you on to the right troubleshooting steps.

[Bob Denman]

Will hyper flash do any damage to the electrical system? I'm in the process of putting on LED lighting, and have it. I kind of like it, but not sure if it will damage the system.

Nope: it's not going to hurt anything!

[bcer960]

I have a2017 RT-s, and have "reset" the hyper flash a few time since adding LED's. This morning, it's back. So, the procedure from Lamont doesn't seem to stick.

I remember reading in a previous post that adding a ?300ohm? resistor inline will also stop it? Anyone remember??

Thanks

[Fatcycledaddy]

I have a2017 RT-s, and have "reset" the hyper flash a few time since adding LED's. This morning, it's back. So, the procedure from Lamont doesn't seem to stick.

I remember reading in a previous post that adding a ?300ohm? resistor inline will also stop it? Anyone remember??

Thanks

Mine didn't stick and kept coming back until I ran through it while the engine is running. Hasn't been back sense.

[Freegle]

I have a2017 RT-s, and have "reset" the hyper flash a few time since adding LED's. This morning, it's back. So, the procedure from Lamont doesn't seem to stick.

I remember reading in a previous post that adding a ?300ohm? resistor inline will also stop it? Anyone remember??

Thanks

If you are going to add a resistor you will need to start at 100ohms and work your way up. I put a 330ohm resister in line with my mirror turn signal and the turn signal was so dim that it almost look like it was not on. I went to a 100ohm resister and everything worked for me. These resistors are half watt resistors and can be purchased at Radio Shack for about a dollar for a four or five pack.

[bcer960]

Mine didn't stick and kept coming back until I ran through it while the engine is running. Hasn't been back sense.

Mine stuck for a week, then came back this morning.

[Matahead]

Sorry, this is the first I heard of this new age remedy... Will the Hazard Hold solution work on all models? Or all models starting a specific year?

I used resistor sets in the 2009 GS, it still hyperflashed.

[Road-Kill]

I take it that the hyper flash occurs when the nanny detects something wrong such as a burned bulb, water in the electric system or a change in some electric draw.

[Lew L]

I had to go with resistors after trying "the fix" a number of times. The resistors work and fix the hyper flash ---- period.


For me---- hyper flash causes-------------- Kaos

[bcer960]

I have also had to resort to resistors, although i was hoping today was the day to install, didn't happen. Can I ask where you mounted them so they were attached to metal??

Thanks
Ray

[Lew L]

I have also had to resort to resistors, although i was hoping today was the day to install, didn't happen. Can I ask where you mounted them so they were attached to metal??

Thanks
Ray

I attached a piece of 16 ga. aluminum to the resistor ( about 1" x 2.5" ) It's just a heat sink. Its been a year since I did this and NO problems.

Kaos

[bcer960]

Thanks Kaos, good idea....

[Matahead]

I have also had to resort to resistors, although i was hoping today was the day to install, didn't happen. Can I ask where you mounted them so they were attached to metal??

Thanks
Ray

Front Resistors on the GS were behind the instrument cluster, on top of the frame end piece. Ground was to the frame, behind the bars, under the lobster Tupperware. Rear were on L brackets I put behind the battery. These brackets held the run-turn-brake module, & resistors. I used one group resistor front, one back, much easier than one each corner.

[bcer960]

Front Resistors on the GS were behind the instrument cluster, on top of the frame end piece. Ground was to the frame, behind the bars, under the lobster Tupperware. Rear were on L brackets I put behind the battery. These brackets held the run-turn-brake module, & resistors. I used one group resistor front, one back, much easier than one each corner.

I only got 2 resistors, one for each direction... you put 4 on? what was the value?? mine are 6.8K at 50W

Ray

[Matahead]

I only got 2 resistors, one for each direction... you put 4 on? what was the value?? mine are 6.8K at 50W

Ray

I had one front, one rear. 4.5k didn't work, completely. They slowed, but not normal.