-
Handlebar Risers for 2013 RS-SM5
Hello, does anyone know where I can get handlebar risers (hopefully 3-inch or more) for my 2013 RS? They changed the handlebar design that year so the earlier riser kits won't fit. Starting in 2013, the handlebars are just stubs at the ends of the center bracket, the throttle cables were replaced by electronic throttle wires, and all wires are encased inside the bracket. This leaves very little slack to install any of the risers for the earlier Spyders. Hopefully someone is making a newer kit, otherwise I will have to do massive rewiring to retrofit an older kit. If a newer kit isn't available, is there another solution to bring the bars up and back a little?
Thanks..Terry
-
Very Active Member
Yes
I just put st handlebars on mine yesterday. Huge difference. They say rts will work also.
Don, t know if there is enough slack in wires or not. I also have 13 rs with sm5.
Took me about 3hrs
-
I think the 14 and 15 RS-S bars are higher than 13 and back. I had a chance to compare a 13 RS-S with can am riser and it was about the same as a stock 14. I will check again with a tape next week. I am happy with my bars on my 14. My height is 5 10.5.. Stay tuned..
-
-
-
Originally Posted by 13janice13
We have the heli bars put on our 2009 Rs, It makes the handle bars one inch higher and four inches towards the driver.They are made out of one piece machined steel- a quality part!
I had those on my 2009 RS also but they won't work on the 2013 because of the change in handlebars design.
-
-
Handlbar
Originally Posted by bmccaffrey
Yes
I just put st handlebars on mine yesterday. Huge difference. They say rts will work also.
Don, t know if there is enough slack in wires or not. I also have 13 rs with sm5.
Took me about 3hrs
what year was the ST? And what all did you have to change to make them work? I get backaches the way my RS is currently set up.
Thanks!
-
Very Active Member
[QUOTE=TerryTheSpyderRyder;960102]what year was the ST? And what all did you have to change to make them work? I get backaches the way my RS is currently set up.
Thanks![/QUOTE
It's a 13 rs sm5
Justhave to trace cables and snip the wire ties.
Hhays posted a good dyi on it.
Took me about 2.5 hrs
Have been riding the last couple of days. HUGE DIFFERENCE. WELL WORTH IT
-
[QUOTE=bmccaffrey;961110]
Originally Posted by TerryTheSpyderRyder
what year was the ST? And what all did you have to change to make them work? I get backaches the way my RS is currently set up.
Thanks![/QUOTE
It's a 13 rs sm5
Justhave to trace cables and snip the wire ties.
Hhays posted a good dyi on it.
Took me about 2.5 hrs
Have been riding the last couple of days. HUGE DIFFERENCE. WELL WORTH IT
Who posted a good DIY on it? I can't find Hhays as a member.
-
Very Active Member
Go under rs-st handlebar swap in the search. It's hchays.
Still there i just looked it up.
-
Originally Posted by bmccaffrey
Yes
I just put st handlebars on mine yesterday. Huge difference. They say rts will work also.
Don, t know if there is enough slack in wires or not. I also have 13 rs with sm5.
Took me about 3hrs
TheVBasdfghj
The ST bars worked perfectly, took some "doing" but I didn't have to cut anything, just buy ST wire covers for the bars. I don't know why Can-Am changed the bar design for 2013, just made changing the bars a chore..
-
Very Active Member
Originally Posted by TerryTheSpyderRyder
I don't know why Can-Am changed the bar design for 2013, just made changing the bars a chore..
Probably because people were moaning they couldn't fit RT bars on the RS because the mounting was different:-)
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|