-
-
Very Active Member
Remember to put the two rubber bumpers back on that piece before reinstalling it.
Or your windshield will get scratched up
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Active Member
Looks good 👍
Sent from my VS990 using Tapatalk
14 RT-S , Stock Large brake pedal White Pearl
-
Very Active Member
looks good
That looks good. I was thinking about chroming mine, but it don't seem to make to much of a difference in the look since it's behind the windshield IMO. I like this idea and might do the black coat instead.
2012 Spyder RT Limited Lava Bronze (Psalm 27:1;Luke 12:4,5)
-
Looks Great, I did the same thing to my RT.
-
Very Active Member
For a more durable finish I had mine powder coated a "Satin Black" be sure to put screws in the front holes that have threads, let the screw stick out at least a 1/2 inch so that the powder coat gets in all areas, failure to put screws in it before painting or powder coating will result in paint messing up the threads. Also ask the powder coater to pug the 6 holes in the back where the sleeve go or you will have to use emery cloth so the sleeves will go back in.
And don't forget to replace the two rubber bumpers on the front.
Cruzr Joe
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Update
I ended up taken the bracket to get powder coated. The paint from the can scratched to easy. So, now the results from powder coated
20160120_170928.jpg
20160120_191135.jpg
-
Very Active Member
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Very Active Member
That's a very sharp looking job.
Artillery lends dignity to what would
otherwise be a vulgar brawl.
******************************
Cognac 2014 RT-S
-
Very Active Member
SPRAY CAN PAINT
Last edited by BLUEKNIGHT911; 01-22-2016 at 01:15 AM.
-
Originally Posted by [COLOR=#b22222
Of course DO NOT DO THIS WITH >>>>PLASTIC PARTS........Mike [/COLOR]
Tried once in the 80s to unwarp a record (big black plastic disk for all the kids out there) by putting it in the oven. Would have worked had I remembered that it was in the oven.
-
Very Active Member
-
Very Active Member
Powder Coated mine and it is the best $50 Farkle on my Spyder!
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|