-
Active Member
Flashing led's spyderpops bumpskid
I want to add a switch and flasher to my spyderpops bump skid that came with leading edge led's
I lead funeral escorts for the local Patriot Guard missions and have always had white led's that blink or strobe. I think a flashing bump skid would add visibility during processions.
Anyone have any thoughts or comments about what I need to do. I have the flasher setup for my hyperwhites, but the (separate) flasher is only working two pods of 16 led's each. It's spec might be for up to 6 pods so 96 led's. I could try wiring that in the circuit, but it seems there's lots more led's on the bump skid.
Any specific component you can point me at would be appreciated. I'd wire in a 2 throw switch so it's either solid on for normal use, or flashing for processions.
thanx
we always run our emergency flashers for such events. good news is I have the fender tri-led kits to be wired into the turn signals.
I'll then be thinking of what I want to do with the rear. It would be some kind of white led's that flash.
let's ride safe & be careful out there,
Mike in Nawlins'
2014 Black SE6 Limited "Charlotte"
New Orleans Ride Captain
Patriot Guard Riders
-
Very Active Member
2015 RT Limited Intense Red Pearl
-
Active Member
Remote
I have the spyderpops remote, its awesome..........
-
Active Member
I bought a same make/spec unit from amazon and tried it. The unit says it's 12amp, but the instructions spec shows 6amp. Regardless, the receiver got very hot and had very little effect on the led's. The remote was working (red light on when button pushed). Either it's defective, miss marked for 6amp, or isn't going to work because of too many led's and load.
Bought another and will see and report.
let's ride safe & be careful out there,
Mike in Nawlins'
2014 Black SE6 Limited "Charlotte"
New Orleans Ride Captain
Patriot Guard Riders
-
Active Member
Originally Posted by PatriotRider
I bought a same make/spec unit from amazon and tried it. The unit says it's 12amp, but the instructions spec shows 6amp. Regardless, the receiver got very hot and had very little effect on the led's. The remote was working (red light on when button pushed). Either it's defective, miss marked for 6amp, or isn't going to work because of too many led's and load.
Bought another and will see and report.
duh...I had the polarity right but not the flow...as in the correct end connected to bike/battery side and the other connected to the led's
now that it's correct, works fine and is very cool.
let's ride safe & be careful out there,
Mike in Nawlins'
2014 Black SE6 Limited "Charlotte"
New Orleans Ride Captain
Patriot Guard Riders
-
Active Member
Besides turning the LED's on and off, strobe lights, dim lights…what else does the remote allow you to do?
-
Very Active Member
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Active Member
I was hoping for "white".....
-
Very Active Member
Originally Posted by Synthetic
I was hoping for "white".....
YOU WANT WHITE, YOU CAN'T HANDLE WHITE, wait a minute that was another argument, let me see if he has "White", yes he said that he has any color "White" that you want.
and next week he will be getting in some "White Ones"
Anonymous
2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer
-
Active Member
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|