Results 1 to 7 of 7
  1. #1
    Registered Users Dragonrider's Avatar
    Join Date
    Feb 2009
    Location
    Canby, OR
    Posts
    3,073
    Spyder Garage
    0

    Default The Missing Rock Guard

    I know everyone's atwitter about the sway bar - just remember the cost of a new belt is MORE than the cost of a sway bar.

    Ron's guard will not keep ALL rocks out of the belt, just the critical big ones! Ride on fresh chip seal, and you will still get a bit of "crunching" going on, but the belt will survive that - the big rocks, not so much.

    The guard comes with MORE than you need to do the job - Ron even includes new clip-nuts, so you don't have to break your wrist putting CanAm's 10mm nuts on the back side of the Spyder's tupperware (thanks for that one Ron!) when you are putting it all back together.

    I bought one for my 2010 RT, after losing my first belt, and it was my FIRST farkle on my new RT. This is one thing that every Spyder should have. Really.
    2014 RT SE6 Rider
    X - Honda Rider
    X - RT S driver
    X - RS driver
    Lifetime VFW Member

  2. #2
    Registered Users
    Join Date
    May 2014
    Location
    Texas
    Posts
    111
    Spyder Garage
    0

    Default


  3. #3
    Active Member Bluehole's Avatar
    Join Date
    Feb 2014
    Location
    Sequim, WA
    Posts
    183
    Spyder Garage
    1

    Default

    +1
    Bob


  4. #4
    Very Active Member Cruzr Joe's Avatar
    Join Date
    Jul 2012
    Location
    Bryant, Arkansas
    Posts
    10,146
    Spyder Garage
    0

    Default

    Quote Originally Posted by Dragonrider View Post
    I know everyone's atwitter about the sway bar - just remember the cost of a new belt is MORE than the cost of a sway bar.

    Ron's guard will not keep ALL rocks out of the belt, just the critical big ones! Ride on fresh chip seal, and you will still get a bit of "crunching" going on, but the belt will survive that - the big rocks, not so much.

    The guard comes with MORE than you need to do the job - Ron even includes new clip-nuts, so you don't have to break your wrist putting CanAm's 10mm nuts on the back side of the Spyder's tupperware (thanks for that one Ron!) when you are putting it all back together.

    I bought one for my 2010 RT, after losing my first belt, and it was my FIRST farkle on my new RT. This is one thing that every Spyder should have. Really.

    I did not know that Ron made rock guards ............................... I thought that Spyderpops made the Rock Guard, did i miss a memo somewhere???

    Cruzr Joe
    2018 F3 Limited, BRP Driver Backrest, Spyderpops Lighted Bump Skid, Dual Spyclops Light, Mirror Turn Signals, Laser Alignment, Engine LEDs, Fog Lights With Halo's, Cushion Handgrips, BRT LEDs, and Under Lighting, Lamonster IPS, (with Clock), F4 25" Vented Windshield with Wings, Airhawk "R" Cushions. Position 4 Brake setting, Short reach Handlebars, Dash Mounted Voltmeter and 12 Volt Plug. Set of 3rd pegs. Extended Passenger Seat. Exterior BRP Connect setup, Ultimate Trailer

  5. #5
    Very Active Member spacetiger's Avatar
    Join Date
    Sep 2013
    Location
    N. Va
    Posts
    647
    Spyder Garage
    0

    Default

    I know its an older thread, but where is the pic?
    13 ST Limited F/R suspension, Corbin, GIVI top case

    16 Vespa Primavera 150: Stock
    16 Piaggio BV350: Suspension, braking mods in work
    14 HD XL1200T: F/R suspension and brake mods; Corbin saddle and bags
    09 Aprilia SC250: F/R suspension and minor brake mods
    97 Honda PC800: F/R wheels, F/R suspension, and F/R brake Mods; Corbin saddle
    90 CB-1: In work, long term project
    89 Honda NT650: F/R suspension; Corbin saddle

  6. #6
    2010 RTS-SE, Orbital Blue
    Join Date
    Sep 2009
    Location
    illinois
    Posts
    1,305
    Spyder Garage
    0

    Default

    Quote Originally Posted by spacetiger View Post
    I know its an older thread, but where is the pic?
    Go to the Spyderpops products page, you should be able to see a picture of it.

  7. #7
    Active Member robtdonna's Avatar
    Join Date
    Jul 2014
    Location
    Ellijay, Georgia, United States
    Posts
    474
    Spyder Garage
    0

    Default

    Once it is installed it is hard to take a pic of, I tried

    Quote Originally Posted by retired1 View Post
    Go to the Spyderpops products page, you should be able to see a picture of it.
    Current: "Scarlett", 2017 Can Am F3-T, SE6, Intense Red Pearl.
    BRP heated grips, DIY brake light strip and turn signal strips, Chrome/LED brake light tag frame, SpyderPops bumpskid, Baja Ron swaybar and billet links, Lamonster Third Peg, BRP Adjustable Passenger Backrest, SpyderPops Missing Belt Guard, ShowChrome oversize brake pedal, TricLED foglights.


    Previous: "Synthia", 2014 Can Am Spyder RT, SM6, Pearl White.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •