-
Active Member
So your rubbers broke? Mine too! Try this alternative...
Okay, so now that I got your attention....The Rubbers on my Mono Cowl Seat broke again and of course, the special rubbers are no where to be found. So my fabricating spouse and crafty/sewing me had a discussion on what an expensive racket that can become...buying and breaking rubbers weekly....so we came up with this. We have shared the "fix" with Spydroe and Spyder114...they agree that this is fast, cheap and longer lasting. We bought the supplies at Michaels...warning: we bought grommets to give it a finished look...but decided that the metal would put too much pressure on the hooks underneath the cowl and may cause a break or bend.
Buy this at any craft store...two sided Velcro Strips.
Cut four strips long enough to overlap each side; allow extra to travel around the seat and hydraulic ram.
Use a hole puncher to center punch a hole about 1/2 inch in from one end. It does not matter whether you place the strip face up or down as each side of the Velcro is different. As you wrap the strips underneath the seat just feel which sides grab.
We placed the back strips underneath the hydraulic ram, so it does not interfere with the function.
After you attach and detach a few times, you can do it with your eyes closed! You can remove the mono cowl in seconds...it does not matter if you ruin or lose the strip; just make another!
Nothing to see in the last picture...just wanted to show off my ride! Turning over 5,000 miles this week! Thank you Spydroe for the bling and helping me to post this for everyone!
Carol Smead
2010 RTS Blue, gone but not forgotten
Former owner of 2008 PE #1032 Yellow
-
Re: So your rubbers broke? Mine too! Try this alternative...
Purchased the cover and right away I didn't like the "rubbers". I'll try your fix, that is if I ever take it off. ;D
-
Active Member
Re: So your rubbers broke? Mine too! Try this alternative...
We (fellow spyderryder Pat and I) found that with the constant movement, bumps, road heat etc. the rubbers rub, dry out and the knobs break off. You might not notice until you have only two holding on. Please check them frequently or you may lose your cowl someday.
Carol Smead
2010 RTS Blue, gone but not forgotten
Former owner of 2008 PE #1032 Yellow
-
SpyderLovers Founder
Re: So your rubbers broke? Mine too! Try this alternative...
Cool mod :bigthumbsup: I'll move this to the "How To" section.
-
Registered Users
Re: So your rubbers broke? Mine too! Try this alternative...
That is such a simple and great way to hold the cowl on. I don't think a strap is going to break ever but at least you don't have to wait two weeks or more and pay ten dollars for new rubber snubbers. Nice Job Carol :bigthumbsup:
-
Re: So your rubbers broke? Mine too! Try this alternative...
Originally Posted by Spydroe
That is such a simple and great way to hold the cowl on. I don't think a strap is going to break ever but at least you don't have to wait two weeks or more and pay ten dollars for new rubber snubbers. Nice Job Carol :bigthumbsup:
Good job I fixed mine as soon as Pat told me what you did. That works GREAT !!!!. Nice job Carol. You missed a really nice ride on Thursday, sure wish and your hubby could have gone with us. Pat's 88 year old dad went with us, rode that baby just fine.
John, Spyder # 114
-
Re: So your rubbers broke? Mine too! Try this alternative...
How are you keeping your velcro straps secure on the cowl anchoring posts .....I made my slot in the straps just large enough to go over the posts but with a little movement or adjustment of the cowl and I have a loose strap that comes off the post?? I still think it's a shame that anchoring this baby has turned in to an owners do it yourself project....the cords that come with the unit 100% Mickey Mouse!
-
Active Member
Re: So your rubbers broke? Mine too! Try this alternative...
Buelldog; husband Bob suggests this...
Take the two longest straps and punch two holes in each of the two straps; 1st hole about 1/2 from end and 2nd 2.5 inches from the end.
Turn over mono cowl. At the widest part there are three torx screws holding the backrest pad to cowl. Remove the two outer screws. Place straps with the end holes of strap through screws between pad and cowl, tighten screws. Now place the 2nd hole through the hook on the cowl. When you overlap the straps make them a snug fit...not super tight...don't want to put pressure on the hooks of the mono cowl.
Just take the 2nd set of straps, looping the hook through the punched holes...remember that these straps go outward around the seat bottom, over the hydraulic ram, laying snuggly against each other.
Carol Smead
2010 RTS Blue, gone but not forgotten
Former owner of 2008 PE #1032 Yellow
-
Registered Users
Re: So your rubbers broke? Mine too! Try this alternative...
Originally Posted by csmead
Buelldog; husband Bob suggests this...
Take the two longest straps and punch two holes in each of the two straps; 1st hole about 1/2 from end and 2nd 2.5 inches from the end.
Turn over mono cowl. At the widest part there are three torx screws holding the backrest pad to cowl. Remove the two outer screws. Place straps with the end holes of strap through screws between pad and cowl, tighten screws. Now place the 2nd hole through the hook on the cowl. When you overlap the straps make them a snug fit...not super tight...don't want to put pressure on the hooks of the mono cowl.
Just take the 2nd set of straps, looping the hook through the punched holes...remember that these straps go outward around the seat bottom, over the hydraulic ram, laying snuggly against each other.
Now that you are a pro now posting pictures, how about a picture of this thread? You can bitch me out the next time I stop by.
-
Re: So your rubbers broke? Mine too! Try this alternative...
Yeah , mine broke too... I'll do the "Velcro fix" as you guys have ... nice job !!!
-
Happy Spyder Owner - 2008 Millennium Yellow PE #2475
HID lights, fog lights, Hindle exhaust, heated grips, anti-vibe bars, passenger extension pegs, BRP custom seat, seat cowl, sport rack/backrest, BRP saddlebags, CHAD black/smoke windshield, outdoor cover, Garmin Quest GPS, Rear axel billets.
-
I'm about to do this to mine as well since after only 2 weeks of it being installed (first time removed) i noticed that oen of them was broke arghhhhhh
Anyone know the aproximate size to cut the strips ?
Happy SE5 Owner!!!
Silver/Black SE5 - Trunk Liner, 1" riser, 12v, Kuryakyn ISO Grips, 5" Kewlmetal Pullback Bars, Kewlmetal Console, Zumo 450, Ipod, Kewlmetal Highway brackets with Wing pegs, Triple Play, Wizard Light LED's, Corbin front/rear saddle with Backrest, Nelson Rigg CL950 Saddlebags with CL800 Tote Bag, CalSci Medium Windshield.
-
Registered Users
This is a great mod. I dont take on and off the cowl very often. So I havent had any problems with the rubber cords holding the cowl on (that I knew of). This past sunday, I my nephew wanted a ride. I went to remove the cowl and found the 2 of the 4 cords were already broken.
I remembered reading this thread and went to wal-mart today to get some velcro. I got the 30" x 5/8" black soft sew on velcro.
NOT THE STICKY BACK. I cut the 30" strips in half. Folded over one of the ends about 1" and put a single punch hole in the strip. The Fold over is to help not rip so easily. I slipped the velcro over the tab where the rubber strap went, using the hole I just made. Then I followed the above directions for strapping it to the seat.
Works Great. I might go ahead and get some sticky back velcro and attach it to the bottom of my seat to make it easy to velcro on and off.
Kalavera
Red 2008 SM5
6-spoke Mag wheels w/Wheel Trim Rings painted RED
Spyder Brake Caliper Trim Kit
Red Mono Seat Cowl
Red rear Sport Rack
Fog Lights
Two Brothers Carbon fiber dual exhaust
Trunk Liner organizer w/12 volt dc outlet
-
Looked at mine today and 2 of the 4 were already broken, after just 3 weeks on the Spyder. Velcro mod, here I come.
Really dont want to chase this thing down the road if it comes off.
-
Registered Users
Just seeing this now. Thanks for the fix description and pictures. Those little rubbers with the knobby ends were junk!!!
Thanks!!!!
-
Registered Users
Went to put gas in the tank and saw these little black balls rolling around. Off to get some velcro, too.
I hope BRP is reading about this so that they can come up with a better way to attach the seat cowl.
Obviously, their way isn't working.
I LOVE my
A positive attitude may not solve all your problems, but it will annoy enough people to make it worth the effort.
-
Registered Users
Darn it...
Just got the mono seat cowl delivered today...what a pain those little rubbers are. Then I bought the one sided velcro...guess I should have read directions a little better.
-
Active Member
Great mod! Am looking to pick up the Cowl and this will work out great!
Thx!!
-
Registered Users
-
Mod Maniac
ata = allergic to asphalt
My mods: https://www.spyderlovers.com/forums/...ead.php?t=5753
.
There are two kinds of people: (1) those who can read, reason and apply the experiences of others; and (2) those who just have to pee on the electric fence. ataDude, 2009
My Spyder:
-
Registered Users
Originally Posted by ataDude
Based on your avatar pic, I doubt you'd get an opportunity to use it.
I don't care who you are, that's funny right there!
-
Registered Users
Rubber
ataDUDE,
I think you hurt my feelings...
"LIFE WON'T CHANGE UNTIL YOU CHANGE YOUR LIFE"
-
Mod Maniac
Originally Posted by porboy
ataDUDE,
I think you hurt my feelings...
Sorry about that.
.
ata = allergic to asphalt
My mods: https://www.spyderlovers.com/forums/...ead.php?t=5753
.
There are two kinds of people: (1) those who can read, reason and apply the experiences of others; and (2) those who just have to pee on the electric fence. ataDude, 2009
My Spyder:
-
Registered Users
Rubber
"LIFE WON'T CHANGE UNTIL YOU CHANGE YOUR LIFE"
-
I had my seat cowl fitted last thursday (it was in for its 15,000 km service anyway) and today being tuesday, Ive noticed that three of the rubber tie downs are broken. I was hoping that they would have lasted at least a week before I had to start looking for the velcro replacement.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|