Results 1 to 25 of 40

Hybrid View

  1. #1
    Registered Users
    Join Date
    Feb 2013
    Location
    Lorain, Ohio
    Posts
    30
    Spyder Garage
    0

    Default BajaRon anti-sway bar install

    Ok last week I got my bajaron anti sway bar. I'm dying to install it, but unfortunately, my frunk is currently not working. So my question is. How difficult is it to install the bar without removing the frunk

  2. #2
    Invalid Emails
    Join Date
    Sep 2012
    Location
    Clermont Florida
    Posts
    474
    Spyder Garage
    0

    Default

    Remove two bottom frunk bolts right and left and pry back to gain room to remove the bolts and slide the bar out.

  3. #3
    Senior MOMENTS Member MrLooney's Avatar
    Join Date
    Sep 2012
    Location
    Salem, Oregon! BUDDAH'S Country
    Posts
    505
    Spyder Garage
    0

    Default Install Anti Sway Bar

    It is very easy even if your just a little mechanically inclined. jack up the front of your about a foot off the ground. You can loosen the bottom of the Frunk or just wedge a 2X4 and spread Frunk away from the frame. Remove the old Anti Sway Bar. KEY POINT INSTALL ALL NEW HARDWARE THAT CAME WITH THE SWAY BAR. Wrap a find wire or string around the new bolts. Then feed the wire or string up through the "U" bracket and hole in the frame to pull the bolt through instead of using your fingers in such a small area. this will speed your installation time considerably. Loose fit the new sway bar and center the best you can. Tighten all bolts and then check any other bolts you may see just a precautionary measure. Maybe take you 1.5 to 2 hours trime. Now put your Spyder on the ground and find the TWISTIES AND GO LIKE A BAT OUT OF HELLO!!

  4. #4
    Very Active Member Chupaca's Avatar
    Join Date
    Oct 2012
    Location
    San Diego, CA.
    Posts
    31,097
    Spyder Garage
    1

    Default Let's see..!!

    If you got your bar from Ron the instruction are clear on changing procedures either way. It is quite simple if you take your time. Good luck your going to love your new unit...
    Gene and Ilana De Laney
    Mt. Helix, California

    ​2012 RS sm5
    2012 RS sm5 , 998cc V-Twin 106hp DIY brake and park brake Classic Black

  5. #5
    Registered Users
    Join Date
    Feb 2013
    Location
    Lorain, Ohio
    Posts
    30
    Spyder Garage
    0

    Default

    Oh yeah I definitely got the instructions. It just seems like Ron recommends removing the frunk. I was just wondering if it is difficult to do without removing it. I'm sure I will get it on there. I'll keep you all posted
    Last edited by JasonAM; 03-29-2013 at 02:27 AM.

  6. #6
    Very Active Member jthornton's Avatar
    Join Date
    Feb 2013
    Location
    Poplar Bluff, MO
    Posts
    2,398
    Spyder Garage
    0

    Default

    I just installed a BajaRon sway bar last week and the instructions do not tell you to remove the frunk. If your doing this on your own cut a 2" long piece of 2x4 and after following the instructions to remove the needed bolts and fasteners to be able to lift the frunk up enough to remove the sway bar put the 2x4 between the frunk and the frame and it will hold the frunk for you.

    On your first ride as spring is approaching move your windshield all the way up so you don't eat too many bugs with that big smile...

    John

  7. #7
    Very Active Member
    Join Date
    Sep 2010
    Location
    Not Here
    Posts
    92,464
    Spyder Garage
    1

    Default

    Hi Jason! Even I managed to get the job done with the frunk still on the bike... Once you get the Spyder up in the air; it's pretty easy to see what you need to do in order to be able to get to the "clamps" that hold the bar in place. There's two bolts that hold the frunk down there; pretty close to the clamp's attaching points. pull them out, and GENTLY pry the frunk out about an inch or so... and prop it in place on each side. (That way you can remove a prop to work on a side...) You can get to those clamp bolts easier if you kind of contort yourself so that your upper "wrenching arm" enters the tangle of Tupperware from out front; just above the "wings"...Good luck!
    2010 RT A&C, RT-L, RT-L , Orbital Blue, Cognac, Jet Black

  8. #8
    Very Active Member StanProff's Avatar
    Join Date
    Jun 2011
    Location
    Jonesborough Tennessee
    Posts
    1,295
    Spyder Garage
    0

    Default

    Quote Originally Posted by JasonAM View Post
    Ok last week I got my bajaron anti sway bar. I'm dying to install it, but unfortunately, my frunk is currently not working. So my question is. How difficult is it to install the bar without removing the frunk
    ON the RT the frunk needs to be open to pop off the service panels on the left and right and then to remove the bolts #68 in the instructions. If yours is a RS it may be different.
    Happy Spyderlovers

  9. #9
    Active Member ABQAndy's Avatar
    Join Date
    Nov 2012
    Location
    Albuquerque, NM
    Posts
    226
    Spyder Garage
    0

    Default

    I did my install last week and it went well, about 2 hrs. I am assuming that when you say your frunk is not working that you can't open it? If that is the case I don't think I would try to take out the two bottom bolts and pry the frunk forward to do the install because you might damage the tupperware Just my thoughts.

    2012 Spyder RT Limited
    Guardian Bell (gift from son)
    Spyderpops bumpskid
    ISCI hand brake
    BajaRon Anti-Sway Bar
    BRP Adjustable Wind Deflectors

  10. #10
    Active Member
    Join Date
    Jan 2013
    Location
    San Diego area
    Posts
    170
    Spyder Garage
    0

    Post Sway Bar

    You defininately need to remove those two upper bolts to prevent damaging the upper end of the frunk.

  11. #11
    Invalid Emails
    Join Date
    Mar 2012
    Location
    Gore,Quebec,Canada
    Posts
    1,744
    Spyder Garage
    1

    Default

    My BajaRon bar is at the post office, waiting for me to pick it up. Just arrived, I can't wait to put it on!lots of time though as there is still about 3 ft of snow on the ground and a huge snow bank in front of the door where the Spyder is resting!
    2012 RT , stock Lava Bronze

  12. #12
    Very Active Member Sarge707's Avatar
    Join Date
    May 2009
    Location
    Connecticut
    Posts
    3,658
    Spyder Garage
    0

    Default

    I tried the block of wood stuff BUT it got in the way- I Had a Trolley jack on the front bottom of trunk "Centered" and as you jack it moves froward slightly and did a great job of keeping the trunk up and out of the way and you could still lay down on either side and work.

    2015 F3 sm6, Custom Dynamics fender lights.

    Sea Doo GTI-SE 90 Jet Ski!!

  13. #13
    SpyderLovers Sponsor BajaRon's Avatar
    Join Date
    Aug 2007
    Location
    Greeneville, TN
    Posts
    13,519
    Spyder Garage
    0

    Default Bajaron Custom Sway Bar Install

    The install instructions vary somewhat depending on which Spyder model you have (RS series or RT series). I believe you have an RS series Spyder.

    The RS series Spyders have a very easy Frunk removal process. It is easier to install the Sway Bar with the Frunk off but I detail the install procedure for both Frunk off and Frunk on methods. Either will work and both are relatively easy.

    The RS series Spyders have a much more difficult Frunk removal process and I do not recommend it, nor do I give instructions for this approach on the RT model Spyders. It is much easier and quicker on the RT's to simply remove 4 bolts (2 upper and 2 lower) so that the Frunk can be moved the 3 or 4 inches necessary to do the sway bar install.

    I highly recommend what I almost never do. Read through the instructions completely before beginning the install. I know, I get excited and I just want to put my new farkle on and try it out. But reading completely through the instructions with a focused head will not take very long and it will pay off every time.

    Good luck and let me know if you need any help.
    Shop Ph: 423-609-7588 (M-F, 8-5, Eastern Time)

    Only SLOW people have to leave on time...





  14. #14
    Registered Users
    Join Date
    Feb 2013
    Location
    Lorain, Ohio
    Posts
    30
    Spyder Garage
    0

    Default

    Yeah I got the RS-S. I was reading the instructions last night shouldnt be a problem. This will be my Friday night project

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •