-
Body screws
Does anyone where I can purchase the screws(bolts) that hold the tupperware together on an RS?
BRP wants too much for them. I was hoping to find a source that's a little cheaper.
Thanks
Rick
-
Originally Posted by lotsasawdust
Does anyone where I can purchase the screws(bolts) that hold the tupperware together on an RS?
BRP wants too much for them. I was hoping to find a source that's a little cheaper.
Thanks
Rick
Forget 'em. Replace them with 14 mm Dzus fasteners available at Kurveygirl.com. You'll be able to peel your plastic faster than a hungry monkey peels a banana.
-
Very Active Member
Originally Posted by Neez
Forget 'em. Replace them with 14 mm Dzus fasteners available at Kurveygirl.com. You'll be able to peel your plastic faster than a hungry monkey peels a banana.
Are these like the three on the left side panel or something different?
Very Happy '08 Spyder RS Owner
-
Thanks Neez. I ordered some tonite.
Rick----
-
I got my screws from Kurveygirl.com today. Fast shipping. The screws work great. I can remove my tupperware real easy now. The advice I've gotten from this site is very helpful. Thanks all!
Rick------
-
Banged Up Member
Would these screws hold true with the RT??
Chris
-
I'm not sure. Are the screws on an RT the same size and length? Hope someone else can answer. The ones I used were 14 mm dzus. They also come in 12mm.
Hope this helped.
Rick
-
...in the pink (Girls On Spyders)
Thanks...I'm going to order a few things from this website...kurveygirl.com
this past summer one of the screws from under the seat fell out (my bad...didn't tighten it all the way back) and when it fell out of all places it hit the ABS trigger wheel and bent 6 or 7 of those thingies ...I went into "Limp mode"...we took a hammer and chisel and straightened them back...I have put another 6,000 miles on the bike and all seems to be OK....so I really want some spares.....
#IamARyder #RideASpyder #CanAmSpyder
-
10 packs out of stock but they do have 6's.
-
Registered Users
Lost one from under the tail section while working on a project and never could find it - took a screw to the local ace hardware and had them match it up - Stainless Steel - but worked well and at about a $1.00 a screw sure beat the BRP price.
Bill
Very Happy Spyder Owner
Gulf Coast Spyder Ryders -- look for us in the Ryder Group/Club shortcut on the homepage.
New Ryders always welcome!!!
-
Active Member
Dzus fasteners
I changed all my torx screws to Dzus fasteners tonight. A Dremmel tool is very handy for this job.
What a useful and easy mod. Thanks for the good tip. I used 14mm all the way around.
-
Registered Users
I've gotta do that to my RTS....
Originally Posted by mooneych
I changed all my torx screws to Dzus fasteners tonight. A Dremmel tool is very handy for this job.
What a useful and easy mod. Thanks for the good tip. I used 14mm all the way around.
How many did you buy and did you use any D rings or all button heads and did you do the bottom pieces too?
Thanks
Tuck
-
Very Active Member
Did I read that right on Kurvygirl or am I missing something?..$6.00 for one 14mm button head?..Sounds kind of expensive to do a whole Spyder..
-
Registered Users
Originally Posted by cyclelover63
Did I read that right on Kurvygirl or am I missing something?..$6.00 for one 14mm button head?..Sounds kind of expensive to do a whole Spyder..
It is, I spent $120 to do my RS 😏
Sent from my iPad using Tapatalk HD
-
Very Active Member
Originally Posted by hrbeta
It is, I spent $120 to do my RS
Sent from my iPad using Tapatalk HD
I wouldn't mind spending that kind of money, if I didn't have enlarge the notches. With my luck, I'll screw that part of it up.
-
Trimming the notches with a dremel was not the way to go. It was fast and simple with a pair of side cutters on the plastic and I found you just need to put the clips on from the side on the steal tabs.
-
Active Member
Body screws/Druz fastners
I just checked the Kurveygirl site and they have 10 packs of 14mm fasteners for $30 a pack, that's about $3 a fastener, pricey, but should be worth it in saved time. I never counted all the screws I had to remove to strip but I don't think it was 40. I could be wrong, wouldn't be the first time .
2009 GS SE5 Silver
-
Very Active Member
Dzus
Originally Posted by lotsasawdust
Does anyone where I can purchase the screws(bolts) that hold the tupperware together on an RS?
BRP wants too much for them. I was hoping to find a source that's a little cheaper.
Thanks
Rick
I changed most of mine to Dzus fasteners like the ones on the tupperware at the oil tank. I got them from http://www.kurveygirl.com/ . There alot cheaper than the screws and it's make for easy tupperware removal and remounting, and no lost screws. That IMHO.
Mike
-
Registered Users
KG
Originally Posted by cyclelover63
Did I read that right on Kurvygirl or am I missing something?..$6.00 for one 14mm button head?..Sounds kind of expensive to do a whole Spyder..
The 16mm that some use on the bottom stuff is $6, plus something like .75 cents for the fastener.
Evidently the 14 mm work ok, with a little extra effort.
Still, the darn things are expensive, but convenient.
Tuck
-
Very Active Member
I think these are a good idea if you remove the panels a lot..I had already bought me a 1/4 " air ratchet that fits great in smaller places from Harbor Freight for app $15.00..That worked out good when I recently installed my handbrake and highway pegs!
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|