Remounting licnese under tail of bike...examples...

[Riker]

I have seen several, and recently someone posted what looked like a very simple mount in a picture, but for the life of me I can't find it again. The mount was connect with couple screws ( under the tail section near the very back under the lights ) and the license was angled back. If you could post yours, or tell me where the mount can be purchased, that would be great!!

Thanks

[arntufun]

Ask And Ye Shall Receive !!!

plate 003.jpg

[5PYD3R]

Here is mine...

[Riker]

hehe..that was it..thank you sir

Where did you buy it ?

Thanks !

[Riker]

Here is mine...

Does it have any lights on it ?

Not sure if that would be legal here or not...

Thanks for posting

[5PYD3R]

Does it have any lights on it ?

Not sure if that would be legal here or not...

Thanks for posting

Lights are in the works right now. Not legal as it is here in MI either. Although I have been followed 3 times by cops (1 state cop) and never got pulled over. I think they just want to see the spyder and either dont notice or dont care? It is actually very visible mounted this way to whoever is behind you.

[Riker]

Haven't traced it back yet. But did you pull the wiring from the original location to light up your "screw lights", or did you just tap off another power source? If tapped off another, did you just cap off the original license plate wiring ?

Sorry for all the questions... really starting to like the idea of removing rear fender...

[arntufun]

This thread will tell you where I got my Bracket an plate light bolts.

http://www.spyderlovers.com/forums/s...=plate+bracket

[arntufun]

Haven't traced it back yet. But did you pull the wiring from the original location to light up your "screw lights", or did you just tap off another power source? If tapped off another, did you just cap off the original license plate wiring ?

Sorry for all the questions... really starting to like the idea of removing rear fender...

You will reroute original wire. it's easy.

[arntufun]

Here is mine...

Whats the deal with you crossing out your plate # WHAT, you don't trust me ???

[5PYD3R]

Whats the deal with you crossing out your plate # WHAT, you don't trust me ???

There are only 2 people in this world I trust, one of them is me and the other isn't you. Name that movie!

On a serious note....ya never know who you can and cant trust these days

[Riker]

Thanks guys... that mount was no longer available, but found similar and order the screw lights as well Soon....soon... (name that movie ) ... hint Mel Gibson and the British

[Gordy]

the patriot

[5PYD3R]

What? Nobody knows my movie? hehe. No hints here and no cheating.

Arntufun: Did those led bolts work pretty good for you then? Light it up pretty well? Was looking between those and some LED strips from Autozone

[Riker]

the patriot

hehe...ding,ding,ding...winner!!!




And thanks for all the input guys!!

[Riker]

Very nice job as well...clean looking

[arntufun]

What? Nobody knows my movie? hehe. No hints here and no cheating.

Arntufun: Did those led bolts work pretty good for you then? Light it up pretty well? Was looking between those and some LED strips from Autozone

I think they work very well and light the plate up nicely. And most importantly............. they are cheap !!!

If you can wait a few weeks, you can get them right from China for only a few bucks.

[Riker]

Too late I am impatient So as mentioned, I ordered a similar model ( Stainless steel ). Little more cost, but got everything for less than $40. Still can't complain, cheap mod compared to what I have spent on other things

Heck, I have already done a mock up pic using a little coloring and cut/pasting to see the look...



I am so addicted to this thing.......

[NancysToy]

Too late I am impatient So as mentioned, I ordered a similar model ( Stainless steel ). Little more cost, but got everything for less than $40. Still can't complain, cheap mod compared to what I have spent on other things

Heck, I have already done a mock up pic using a little coloring and cut/pasting to see the look...



I am so addicted to this thing.......

If you mount your plate vertically like that (as required by some state laws), it will hit the tire with a heavy rider or when carying a passenger on rough roads or big bumps. It can be torn off or damage the Spyder.

[Riker]

Thanks..yeah, it is just my poor cut/pasting abilities...

The actual mount will angle it back to help avoid that issue. As well, I will be putting the shock at max. Mostly ride 1 up, so it should be ok. But I will do a mock install once I get the parts to make sure things will be safe

[bjt]

Lights are in the works right now. Not legal as it is here in MI either. Although I have been followed 3 times by cops (1 state cop) and never got pulled over. I think they just want to see the spyder and either dont notice or dont care? It is actually very visible mounted this way to whoever is behind you.

On our ride out the the Hollywood Owners event, I lost my plate on the first day of the ride just past Cuba, MO. I rode my Spyder from Missouri to California and back to Michigan without any plate and no police officer ever pulled me over.

[5PYD3R]

Too late I am impatient So as mentioned, I ordered a similar model ( Stainless steel ). Little more cost, but got everything for less than $40. Still can't complain, cheap mod compared to what I have spent on other things

Heck, I have already done a mock up pic using a little coloring and cut/pasting to see the look...



I am so addicted to this thing.......

Make sure you angle your plate WAY back. Mine was mounted that way and was torn off on the second ride. If you look in the pic I posted, you can see the damage it did to the tail section. That is why I have it mounted where it is now and that's where it is staying LOL.

[Riker]

Here is the mount and LED's for the project. I think the angle looks pretty good, let me know your comments if not

[Raptor]

There are only 2 people in this world I trust, one of them is me and the other isn't you. Name that movie!

On a serious note....ya never know who you can and cant trust these days

The movie is Con Air, where John Cusack and Nick Cage are having their stare-down...

And you guys have convinced me to take my fender off. The inevitable is happening and the thing is starting to crack, so off it comes.

[5PYD3R]

The movie is Con Air, where John Cusack and Nick Cage are having their stare-down...

And you guys have convinced me to take my fender off. The inevitable is happening and the thing is starting to crack, so off it comes.

Finally someone got it, Congrats! Fenderless is the best!