-
Very Active Member
RT Mirrors - Loose - My fix
With having to remove the Mirrors on the RT everytime the tupperware has to come off they seem to get more and more loose
it also seems that the can be removed with little effort and could be prone to being removed by vandals although they would have to know
the sequence
BRP Sould have come up with a more friendly version - The fittings are prone to being damaged just in normal on/off operation if care is not taken
Having said that I wanted to make my mirrors more secure and less prone to shaking whilst riding
This is what I did
I removed the mirror having marked at the bottom edge where the mirror fits against the bodywork - near to the Headlights
I drilled a hole in the bodywork to take a Cable tie (Zip tie in US)
I drilled a hole in the RT Mirror at the bottom edge so the 2 holes would line up once the mirror was back in place
A Cable tie was threaded through the bodywork then though the mirror - Once the mirror was back on the Cable tie was pulled tight
this secured the mirror to the bodywork - The cable tie sits below the mirror and is not noticable from the front but can be seen under the
Mirror (The excess cable tie is cut off)
When I want to remove the Mirror I just cut the cable tie and replace it with a new cable tie when refitting the Mirror
The cost of a Cable tie is alot less than the cost of a replacement Mirror
As with any modification Photos help to explain how it was done - So here are some and I hope it helps other who may want to secure their Mirrors
SAM_0105 (640x480).jpgSAM_0107 (640x480).jpgSAM_0110 (640x480).jpgSAM_0108 (640x480).jpgSAM_0109 (640x480).jpg
Eddie Sheppard
Reading UK
Spyder – RT-S SES (AUTO 2010 Model)
List of Mods :-
Added Zuno 660 -Garmin kit as supplied on the Spyder RT Limited
LED Bulbs Reversing Lights,Front position lights
HMT - Brake Light
LED – Running lights
LED - Mud Flap lights
Rear extended Mud Flap
Sport Tall Wide Clear Windshield
Utopia Backrest
S/S Grills both sides matching
Bottom Panel S/S Protection
S/S stronger Funk Lid brackets
S/S Bracket for RBNS Hood for Zumo 660 GPS + TourTech Lockable Mount
Rubber Tank protector on glove box
Grip Puppies
Power Socket in Switch Cluster and at Rear passenger Handrail
Rear Speaker Switch for passenger On/OFF
Upgraded Front Marine Speakers
Bluetooth On board Radio to Sena SMH10 Headsets
-
MOgang Member & Monster Member
Also, periodically you need to take needle nose pliers and squeeze the little metal retainer rods back straight. The will bow out after repeated remove/replace. That usually fixes them right up tight again.
-
-
Best fix i have seen to tighten those wobbly mirrors. Thanks a million. Mine definitely need something like your cable tie fix. pinching those wires together that grap the posts only works a few times.
-
they need to design the mirror mounting like Mercedes did theirs. a single bolt. the mirror head folds forward to access the bolt. piece of cake.
just snapped my mirrors back on today, and they are a little loose at the front. already squeezed the clips. going to use the zip tie method on'em tomorrow.
Last edited by quasi; 01-22-2017 at 10:08 PM.
-
Active Member
I just bought a dozen of those clips and change them out when I popped a mirror off. They're available and not expensive. I mean, they're just really good paper clips. My solution but thanks for the idea when my solution no longer works.
-
Ozzie Ozzie Ozzie
There is a VASTLY BETTER solution discussed here:
http://www.spyderlovers.com/forums/s...imited-Mirrors
It really makes all the other solutions look like archaic bandaids & works soooo much better than the OE fittings you'll be gob-smacked!
-
This thread is five and a-half years old...
There's bound to be some improvements over time...
-
mirror parts
Last edited by marty1096; 02-05-2017 at 09:42 PM.
-
Very Active Member
Originally Posted by Bob Denman
This thread is five and a-half years old...
There's bound to be some improvements over time...
Your right Bob (Might as well admit it)
I thought I had posted this in response to this thread
http://www.spyderlovers.com/forums/s...imited-Mirrors
It was not intended to appear as a new thread
As you read through the thread you will see Russell Culley has come up with a great idea for securing the RT Mirrors, So I will try a set of Magic Mirror mounts and use my existing Zip ties as a 2nd line of defence to secure the mirrors
Removal of the mirrors in the future will be easier, Cut the zip tie and remove the mirrors as explained on you tube by Russell Culley
https://youtu.be/gYxJjefNGoA
Eddie Sheppard
Poole Dorset UK
Get a Spyder - See the World
-
Thanks Eddie!
I've ordered his kit also, and am just waiting for the chance to try it out!
-
mirror issues.
used self tapper in middle of mirror plastic to better secure , will also do cable ties mod .
magnets good idea but just too expensive to south Africa with shipping
regards
-
Very Active Member
-
Very Active Member
seriously though
I am looking into the majic mirror inserts for sure ! will check with blue /911 guy ! ( soon as I get uhmmm free )
-
Originally Posted by ddtoit
used self tapper in middle of mirror plastic to better secure , will also do cable ties mod .magnets good idea but just too expensive to south Africa with shipping regards
Make your own. There's a thread from last year showing how to do it.
2014 RTL Platinum
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|