-
RT-S PE# 536
cup holders?
Has any one found any cup holders that fit the RT? Most of what I've seen bolt on to handle bars or brake reservoirs. How about the back seat?
Jay on Omega Bay Texas
Spyder RT-S PE# 536
-
RT-S PE#0391
Cup/Bottle Holder
I think a good idea would be to fashion something that might bracket and hook around the lip of the left-side of the hump storage compartment, then rest neatly forward of the pads.
-
Motorbike Professor
You might want to consider a RAM mount cupholder. I know nothing about cup holders, and I have no understanding why anybody would want one on a motorcycle, but if you do, this may be a good alternative. There are a variety of mounting bases, some of which would bolt readily to a rear body panel, near the passenger. I have mounted one at the center of my handlebars, and there are other alternatives. I usually get my RAM mounts from GPSCity. They also have suction mount cup holders.
-Scotty
2011 Spyder RTS-SM5 (mine)
2000 BMW R1100RTP, motorized tricycle & 23 vintage bikes
2011 RT-622 trailer, Aspen Sentry popup camper, custom motorcycle trailer to pull behind the Spyder
Mutant Trikes Forever!
-
RT-S PE# 536
I have a RAM mount for my GPS on my handlebars also. I have looked at possible places to attach the ball front and rear. Actually, those mounts are versatile enough to attach just about anything you want. I may go that route.
One place I was looking at was under the dash sun shield on the right side. I don't know how substantial the material would be for self tapping screws though. Rear is going to be tougher to find a place that won't interfere and doesn't mess up the aesthetics.
Any other suggestions?
Jay on Omega Bay Texas
Spyder RT-S PE# 536
-
Yeah, I found the perfect holder...she sits right behind me!!!
V.
-
Registered Users
Originally Posted by scudrunner
Has any one found any cup holders that fit the RT? Most of what I've seen bolt on to handle bars or brake reservoirs. How about the back seat?
Here are a couple of photo's I have of what we offer. I will have much better on my web page later this week.
-
My Spyder has no hand brake or clutch, will it fit?
V.
-
RT-S PE# 536
Originally Posted by Vordak
My Spyder has no hand brake or clutch, will it fit?
V.
Mine neither.... do I have to get a hand brake to have a cup holder?
Jay on Omega Bay Texas
Spyder RT-S PE# 536
-
Registered Users
Originally Posted by Vordak
My Spyder has no hand brake or clutch, will it fit?
V.
I have what you need. My web page has now been updated. Take a look and let me know if I can be of help in any way. This is a very clean / neat set up.
-
Registered Users
Originally Posted by scudrunner
Mine neither.... do I have to get a hand brake to have a cup holder?
That would be a good way to sell two things at once. However not very nice. Be happy to sell both, but you don't have to. Check out the web page as it was updated today. Let me know if you have any questions or if I can be of help.
-
Apparently I'm an idiot because I can't find the cupholder on your site....
V.
-
RT-S PE# 536
Apparently I'm an idiot because I can't find the cupholder on your site....
Wow, I never realized it before, but I must be an idiot too!
Jay on Omega Bay Texas
Spyder RT-S PE# 536
-
Originally Posted by Vordak
Yeah, I found the perfect holder...she sits right behind me!!!
V.
-
Very Active Member
Hey Billy, got anything that will mount for the passenger on the RS/GS model?
I have your armrests, thought a cup holder might be nice for a long trip in the summer once I ditch the full face for the 3/4 when the hot weather comes.
We are a happy THREE Spyder family! My Rides: 2008 Quantum Blue Premier Edition Spyder GS SM5 (#1344)
2015 Pearl White / Red Can-Am Spyder F3-S SM6
2016 Intense Pearl Red Can-Am Spyder F3-T SE6
2019 Chevrolet Volt (ER-EV)
2003 Jeep Wrangler Sport X 4.0L I-6
RETIRED Owner / Event Coordinator - Annual Western Regional Can-Am Spyder Rallies
Spyders in the Redwoods and Red Rock Spyder Rally of Southern Utah
The West Coast's Can-Am Spyder Community Ambassador
-
Registered Users
Originally Posted by Vordak
Apparently I'm an idiot because I can't find the cupholder on your site....
V.
The actual cup holder is not on the web page. The accessory kit gets you to a 1" ball that you can mount whatever you want. I do have RAM cup holders here at ISCI. However there are several to choose from. Here is a picture.
This one is mounted to a brake. The kit on my web page mounts it to the handle bar.
-
Registered Users
Originally Posted by ISCI Billy
The actual cup holder is not on the web page. The accessory kit gets you to a 1" ball that you can mount whatever you want. I do have RAM cup holders here at ISCI. However there are several to choose from. Here is a picture.
This one is mounted to a brake. The kit on my web page mounts it to the handle bar.
The RAM part number for the cup holder I have is RAM-B-132BU.
http://www.ram-mount.com/
-
RT-S PE# 536
I hate to be a pain, but your web site is not very easy to find anything and is not intuitively obvious where I might search. If I click on Spyder parts, I get:
1. FLOORBOARDS AND KITS 2. SHIFTER
3. HIGHWAY PEGS AND RISERS
4. PARKING BRAKE EXTENSION
5. MODIFIED PARKING BRAKE EXTENSION
6. BRACKET ASSEMBLIES
7. HAND BRAKE SYSTEM
8. BRAKE LEVERS
9. CRUISERBOARDS
10. PASSENGER ARMRESTS
11. PICS OF PRODUCTS INSTALLED
None of which suggest that it would be a RAM ball attachment kit. Apart from clicking on each one, or scrolling down through the entire set of pictures (which I did and still didn't see the accessory kit), what would you suggest I click on to find the accessory kit?
Jay on Omega Bay Texas
Spyder RT-S PE# 536
-
Very Active Member
Originally Posted by scudrunner
None of which suggest that it would be a RAM ball attachment kit. Apart from clicking on each one, or scrolling down through the entire set of pictures (which I did and still didn't see the accessory kit), what would you suggest I click on to find the accessory kit?
Not to steer you away from ISCI (cuz I love their stuff) but you can get that (and more) at www.mountguys.com.
Drink holder handlebar kit: http://www.mountguys.com/product_p/ram-b-132-1r.htm
Drink holder with RAM ball: http://www.mountguys.com/product_p/ram-b-132bu.htm
Drink holder resevoir ball mount kit: http://www.mountguys.com/product_p/ram-b-132-345.htm
Hope that helps!
We are a happy THREE Spyder family! My Rides: 2008 Quantum Blue Premier Edition Spyder GS SM5 (#1344)
2015 Pearl White / Red Can-Am Spyder F3-S SM6
2016 Intense Pearl Red Can-Am Spyder F3-T SE6
2019 Chevrolet Volt (ER-EV)
2003 Jeep Wrangler Sport X 4.0L I-6
RETIRED Owner / Event Coordinator - Annual Western Regional Can-Am Spyder Rallies
Spyders in the Redwoods and Red Rock Spyder Rally of Southern Utah
The West Coast's Can-Am Spyder Community Ambassador
-
Registered Users
Originally Posted by scudrunner
Click on 2010 Spyder Parts. This is all of the new stuff we have for 2010. This is for both models. If you would like give me a call at 1-800-838-9421 and I can take care of anything you need that we offer.
-
RT-S PE# 536
Well, thanks everyone, I think I'll be fabricating my own.
Jay on Omega Bay Texas
Spyder RT-S PE# 536
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|