Which belt guard is more important - top, or both?

[msgoodwrench]

Bought a used 2008 GS, there are no belt guards on it. I see that Spyderpops sells the 'missing belt guard'. Is it more important to have the top guard, or shall I make sure to get both? Thanks for your comments!

[Freddy]

Get both - it needs em. This was 2 weeks old and before I fitted an inner guard.

[2dogs]

Get both - it needs em. This was 2 weeks old and before I fitted an inner guard.

.....

Oh, oh, That pic almost looks like a dampener gone bad.

[BLUEKNIGHT911]

Bought a used 2008 GS, there are no belt guards on it. I see that Spyderpops sells the 'missing belt guard'. Is it more important to have the top guard, or shall I make sure to get both? Thanks for your comments!

Hi, I sent you a PM about your " ZERK " issue ..... As to the belt guard, adding one will provide " peace of mind ", .... IF a rock should get trapped ( not likely and if the top is smooth not ever ) in the top of the belt - I honestly can't think of anything BAD that this might cause, however that is not the case with the inside of that belt..... I made my own from 26ga. sheet metal, it's larger than what can be purchased and a bit closer to the belt. .... this was easy ( for me ) to make because I had access to a " Bending Brake " ..... before I made this I had already driven 36,000mi. on two different Spyders a GS & an RSS .... I live in Vermont and a lot of those miles were on GRAVEL roads..... I have the one I made on my2014 RT. .... It provides peace of mind - - - priceless..... Mike

[DriftersWay]

Do you have a pic of it. Thanks

[Freddy]

Here's the one I made of sheet metal. It's attached to the lower shocky bolt with a Z shaped bracket on the right and the left side is glued to the swing arm. It's still there after 13 years. I run a 205/55-15 tyre. The slightly narrower tyre give some clearance for the aftermarket inner belt (stone) guard, otherwise it can rub the sidewall.

[2dogs]

Sweet! Thanks for the design and specks.

[msgoodwrench]

Thanks to all for replies! I have gotten both now, Ebay for the bottom one, and SpyderPops for the top. Appreciate your comments and thoughts.

[Deanna777]

Thanks to all for replies! I have gotten both now, Ebay for the bottom one, and SpyderPops for the top. Appreciate your comments and thoughts.

msgoodwrench, My boyfriend and I just installed the Missing Belt Guard from Spyderpops on my 2023 F3 LTD Special. The Missing Belt Guard rubs on the rear tire when the bike is moving forward and in reverse, makes a slight rubbing sound on the rear tire. Have you had problems with your Missing Belt Guard on your spyder?

Deanna

[Mikey]

msgoodwrench, My boyfriend and I just installed the Missing Belt Guard from Spyderpops on my 2023 F3 LTD Special. The Missing Belt Guard rubs on the rear tire when the bike is moving forward and in reverse, makes a slight rubbing sound on the rear tire. Have you had problems with your Missing Belt Guard on your spyder?

Deanna

Deanna this was a older post but your issue's should not be happening, something needs adjusting or you need to go to a skinner tire the wide slicks should not be hitting your guards! Good luck

[Deanna777]

Deanna this was a older post but your issue's should not be happening, something needs adjusting or you need to go to a skinner tire the wide slicks should not be hitting your guards! Good luck

Mikey,

I know that this is in an "older thread. What do you think needs to be adjusted? When it comes time to change to a different/skinny tire. I know that the OEM tire should not be hitting the belt guard.

Deanna

[Peter Aawen]

Mikey,

I know that this is in an "older thread. What do you think needs to be adjusted? When it comes time to change to a different/skinny tire. I know that the OEM tire should not be hitting the belt guard.

Deanna

If it's still the OEM tire Deanna, (& since it's a new Spyder, then I'd guess that it is?! ) then the 'rubbing' you are experiencing is probably at least partly due to the (fairly high for the light load) air pressure you're running in the tire.

However, due to the lighter construction these OEM Kendas have in comparison to most other 'more normal' auto tires, the OEM Kenda tires do NEED the higher pressure indicated on your tire placard just for them to work safely, so I really wouldn't recommend you drop that too much, if at all!! But do be aware that you won't be gaining anything much by running any higher pressure than that shown on your Spyder's tire placard in the Kendas, as some are mistakenly inclined to do.... There's nothing to be gained from running any higher than recommended pressures in the Kendas except maybe even faster/greater wear; increased risk of tire damage due to hitting road debris or potholes; a harsher ride; less traction; increased suspension wear; and a few more things besides; with the only positive that I can think of right now being maybe an ever so slightly better fuel economy!

So I'd suggest that you stick with the Kenda's recommended air pressure until you swap it out, and I guess you'll just hafta put up with the rubbing until you do... sooner rather than later might be a good idea tho, not only to avoid destroying the belt guard, but also for SO many other reasons too! Fitting something like a 205/60R15 should see that rubbing and a bunch of other things discussed elsewhere suddenly become a WHOLE LOT better!

Just Sayin'

[Deanna777]

Deanna this was a older post but your issue's should not be happening, something needs adjusting or you need to go to a skinner tire the wide slicks should not be hitting your guards! Good luck

Mikey,

My tires are OEM tires.

I have 2,000 miles plus on the bike. It is still brand new.


Deanna

[msgoodwrench]

msgoodwrench, My boyfriend and I just installed the Missing Belt Guard from Spyderpops on my 2023 F3 LTD Special. The Missing Belt Guard rubs on the rear tire when the bike is moving forward and in reverse, makes a slight rubbing sound on the rear tire. Have you had problems with your Missing Belt Guard on your spyder?

Deanna

So sorry, just saw your question here. I put the bottom guard on, but did not see a good way to put the top on on my '08. Things didn't line up, and I didn't want it halfway held on, so I ended up not using the top one.

[Deanna777]

So sorry, just saw your question here. I put the bottom guard on, but did not see a good way to put the top on on my '08. Things didn't line up, and I didn't want it halfway held on, so I ended up not using the top one.

msgoodwrench,

OK.

Deanna

[Freddy]

A 205/55-15 solves that problem and is a better fit on the rim.

[Deanna777]

A 205/55-15 solves that problem and is a better fit on the rim.

Freddy,

What brand of tire?

My current mileage is: 1,025.

My boyfriend has the same thing happening on his 2023 S2S.

Deanna

[Freddy]

I think it's a Kumho at present. I've had a few brands on it and run it at 18psi for very even wear.