-
Suggestions for installing fog light cover plate back on left side of 2018 RT?
Any suggestions as to how to get the rear cover plate back on the fog, not enough room in there to get hands right and if removing the air horn is viable any recommendations for that to make room any help would be appreciated!
Thanks in advance.
-
Very Active Member
My 2014 was difficult. Didn't seem like enough room.
Put the bottom in first. You have to slip it in between the housing and that big glob of crap behind the housing whose only purpose is to make your life miserable.
I used my cell phone as a camera see what I was doing.
Once the bottom was in I could push the top in until it locked.
It helps a bit if you swing the handlebars to move the tire out of the way.
This will allow you to wrap your hands around the frunk and touch the top with one hand, and the bottom with another.
Either that, or you have to remove the frunk.
It took me about 20 minutes of slow, careful tedious trial by error, until I got the cap back on.
I found that it helps to lubricate the work with verbal references to BRP, all the BRP engineers, the unmarried parents of the BRP Engineers and frantic calls for help to various deities both real and imagined.
It can be done, but what a PITA.
If it ain't broke, don't break it.
IBA #47122
2020 RT Limited Asphalt Grey
-
Originally Posted by ThreeWheels
My 2014 was difficult. Didn't seem like enough room.
Put the bottom in first. You have to slip it in between the housing and that big glob of crap behind the housing whose only purpose is to make your life miserable.
I used my cell phone as a camera see what I was doing.
Once the bottom was in I could push the top in until it locked.
It helps a bit if you swing the handlebars to move the tire out of the way.
This will allow you to wrap your hands around the frunk and touch the top with one hand, and the bottom with another.
Either that, or you have to remove the frunk.
It took me about 20 minutes of slow, careful tedious trial by error, until I got the cap back on.
I found that it helps to lubricate the work with verbal references to BRP, all the BRP engineers, the unmarried parents of the BRP Engineers and frantic calls for help to various deities both real and imagined.
It can be done, but what a PITA.
Hmm, sounds like some Johnny Walker might be of assistance from the way your describing it but thanks for the tips.
-
Very Active Member
Originally Posted by h100250
Hmm, sounds like some Johnny Walker might be of assistance from the way your describing it but thanks for the tips.
Use the agent of your choosing.
My Go To Guy is Jack Daniels Honey.
If it ain't broke, don't break it.
IBA #47122
2020 RT Limited Asphalt Grey
-
Active Member
My advice
Have plenty of band aids and don't have anyone around that is offended by swearing There is not much room but after fighting with that thing for what seemed like hours I finally was able to get it back. On as stated in another post do the bottom first, it was not easy by far.
-
Active Member
To make more room, remove the snorkel and don't replace it.
Have not noticed any more intake noise.
2015 Red Pearl RT-S
EXO2 heated Vest/Gloves
BAJARONS sway bar
TricLEDS side markers
Xenon Depot LED Head & Fog Lights\
Missing Belt Guard
Bump Skid
M2 Shocks front/rear
Russel Day Long heated seat
-
Ozzie Ozzie Ozzie
Wivwot'Esays! No more noise, & no discernable drop in power or torque! And it makes doing sooo many things under the tupperware a helluva lot easier!!
2013 RT Ltd Pearl White
Ryde More, Worry Less!
-
-
Ozzie Ozzie Ozzie
I took the snorkel bit off my 2013 RT some years back, and have ridden thru more than just a couple of multi-hour long toad-strangling frog-drowning downpours & a few 'hub deep' water crossings since, all without any issues! But it is your call.
2013 RT Ltd Pearl White
Ryde More, Worry Less!
-
Very Active Member
Originally Posted by Peter Aawen
I took the snorkel bit off my 2013 RT some years back, and have ridden thru more than just a couple of multi-hour long toad-strangling frog-drowning downpours & a few 'hub deep' water crossings since, all without any issues! But it is your call.
Peter I see your is a 2013 RT take its the 998 v twin engine
The original poster has a 2018 RT the 1330 triple engine
Would the snorkel be the same position etc on both models
Thanks
Eddie Sheppard
Poole Dorset UK
Get a Spyder - See the World
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|