-
Active Member
2014 RTL SE6 what could cause these Headlight system issues ?
Need someone's help in understanding what is "possibly" happening here, and how to know for sure....then how to fix. Here is what I know :
1. First noticed yesterday that when I started the Spyder, the right front headlamp appeared to be in "high beam" condition, with no light at all in the left light.
2. Tried the hi/lo switch, and the switch would not stay in the lo beam position but the shutter sound (which I actually had never heard before and didn't even know about) appeared, and the right light seemed to show both beams trying to be on for an instant.
3. Pulled both fuses and tried one at a time, but no light from either side unless both fuses were in.
That's where I am right now. I'm tending to lean towards a bad rocker switch on the dash, but............not sure how to check further.
Would 1 burned out bulb cause this ??? Doesn't seem so, but with this setup, who knows....
From searching on this site for "headlight issues", I'm sure this isn't new to some of you. I have read about changing to LEDs and may do so while resolving this.
Any help appreciated.
-
Originally Posted by teninospyder
Need someone's help in understanding what is "possibly" happening here, and how to know for sure....then how to fix. Here is what I know :
1. First noticed yesterday that when I started the Spyder, the right front headlamp appeared to be in "high beam" condition, with no light at all in the left light.
2. Tried the hi/lo switch, and the switch would not stay in the lo beam position but the shutter sound (which I actually had never heard before and didn't even know about) appeared, and the right light seemed to show both beams trying to be on for an instant.
3. Pulled both fuses and tried one at a time, but no light from either side unless both fuses were in.
That's where I am right now. I'm tending to lean towards a bad rocker switch on the dash, but............not sure how to check further.
Would 1 burned out bulb cause this ??? Doesn't seem so, but with this setup, who knows....
From searching on this site for "headlight issues", I'm sure this isn't new to some of you. I have read about changing to LEDs and may do so while resolving this.
I do believe that 1 burnt out bulb makes the working bulb turn into high mode to compensate for the burnt out bulb.
My reason for this is when I upgraded my headlights to led ones I tested one of the new installed leds and it only work in high mode. When I installed the other side everything went back to normal.
Just my 2cents
Joel
Any help appreciated.
I do believe that 1 burnt out bulb makes the working bulb turn into high mode to compensate for the burnt out bulb.
My reason for this is when I upgraded my headlights to led ones I tested one of the new installed leds and it only work in high mode. When I installed the other side everything went back to normal.
Just my 2cents
Joel
-
Very Active Member
Originally Posted by beefybudds
I do believe that 1 burnt out bulb makes the working bulb turn into high mode to compensate for the burnt out bulb.
My reason for this is when I upgraded my headlights to led ones I tested one of the new installed leds and it only work in high mode. When I installed the other side everything went back to normal.
Just my 2cents
Joel
I cannot explain your experience. But looking at the wiring diagram. There is no way for the headlight current to be monitored. So I don't think your theory is correct. Also I have not been in motor vehicle lighting in a lot of years. But when I was it would have been illegal to design a system that cannot be dimmed in some situations.
2018 F3 LIMITED
-
Originally Posted by billybovine
I cannot explain your experience. But looking at the wiring diagram. There is no way for the headlight current to be monitored. So I don't think your theory is correct. Also I have not been in motor vehicle lighting in a lot of years. But when I was it would have been illegal to design a system that cannot be dimmed in some situations.
I can't explain it other than what happened to me when I only had one headlight plugged in. It would stay in high beam. I thought I did something wrong but as soon as I installed the second light everything went back to normal.
-
Beefy is correct if only one bulb is plugged in the high/low beam does not work. The OP has a burned out bulb and it is pretty easy to change. Now would be a good time to go to LED. www.tricled.com
2017 F3T-SM6 Squared Away Mirror Wedgies & Alignment
2014 RTS-SM6 123,600 miles Sold 11/2017
2014 RTL-SE6 8,600 miles
2011 RTS-SM5 5,000 miles
2013 RTS-SM5 burned up with 13,200 miles in 13 weeks
2010 RTS-SM5 59,148 miles
2010 RT- 622
-
Very Active Member
Originally Posted by SpyderAnn01
Beefy is correct if only one bulb is plugged in the high/low beam does not work. The OP has a burned out bulb and it is pretty easy to change. Now would be a good time to go to LED. www.tricled.com
I agree it's a burnt out bulb.
Looked at the wiring diagram again. I don't see how a burnt out bulb will affect the shutters. If someone can actually explain it. That would be great. No guesses.
2018 F3 LIMITED
-
Very Active Member
Power to the bulbs does not go through the hi/lo switch. So the switch cannot be the culprit for one bulb not coming on. Your Spyder has single filament bulbs that come on when the engine starts and first reaches idle speed. Hi/lo is controlled by shutters. So if the bulb is burnt out. Both hi and low will not work on one side. I would start there. If the hi/lo switch will not stay in position. That is a different problem and needs a different solution.
2018 F3 LIMITED
-
Very Active Member
Interesting....🤔
If the hi/lo switch is not operating properly i would start there. It will have to fixed anyway and may be causing some of the problem.
Gene and Ilana De Laney
Mt. Helix, California
2012 RS sm5
2012 RS sm5 , 998cc V-Twin 106hp DIY brake and park brake Classic Black
-
Very Active Member
Originally Posted by Chupaca
If the hi/lo switch is not operating properly i would start there. It will have to fixed anyway and may be causing some of the problem.
The OP needs to make sure he wasn't pushing it to the 'flash' mode. There are three positions of the switch, hi, low, flash. Flash mode is momentary.
2014 Copper RTS
Tri-Axis bars, CB, BajaRon sway bar & shock adjusters, SpyderPop's Bumpskid, NBV peg brackets, LED headlights and modulator, Wolo trumpet air horns, trailer hitch, custom trailer harness, high mount turn signals, Custom Dynamics brake light, LED turn signal lights on mirrors, LED strip light for a dash light, garage door opener, LED lights in frunk, trunk, and saddlebags, RAM mounts and cradles for tablet (for GPS) and phone (for music), and Smooth Spyder belt tensioner.
-
teninospyder, have you implemented any of these suggestions? it would be nice to get some feedback from you. Thanks.
2014 RTL Platinum
-
Active Member
thanks about my headlight issues - status right now
Originally Posted by UtahPete
teninospyder, have you implemented any of these suggestions? it would be nice to get some feedback from you. Thanks.
Sorry I haven't updated the status of my work on this issue. I was really going to....when I had it resolved. Some of these new comments of mine may surprise you.....based on different issues we all face with these things. Other comments I have here won't surprise some of you at all.
First off, I have taken everyone's comments and knowledge about this into my little, getting older by the hour brain, and am currently waiting for my new TricLED headlights to be delivered (maybe even today !).
I have "a lot of hope" from what all of you have provided (and by watching videos about the bulb replacement process), that my issues are REALLY only caused by a burned out left bulb and my own stupidity about the light switch operation. The last few comments I read this AM....about what the light switch does......is probably my whole problem other than the burned out bulb. I admitted before that I didn't know anything about the shutter system being on this Spyder, nor apparently did I know that the "lower position" on the rocker switch was for "flashing for pass". I never had to use it, that I know of, and as I said above I admit to not remembering everything I read in the past from the manuals and elsewhere about all the "gadgets, options, processes, etc," we have at our disposal on a Spyder. No excuses people....just a fact of life for me lately......you should watch me looking for keys or my cell phone !!! :-))
Anyway, I will update after I put in the new bulbs, I promise. Now for my one disappointing comment here.
Along the way in the posting process I received (you can read it) one from BRPCares saying they were sorry to hear of my issues and if I would forward my VIN and contact info they would have a tech get in touch with me and try to help. I sent the info, including my write-up from this forum. The next day I received an email from someone at BRP suggesting only that I take it to a dealer for a diagnosis of the problem. This is a 2014 Spyder RTL, which is obviously out of "factory" warranty. When I queried back whether or not this would be "free", the answer was NO. Unless it was found to be a warranty issue I would have to pay for the dealer check. That is the extent of the entire conversation to me from BRPCARES.
Now, what did I expect? I expected per the original post they made to me at this forum that I would receive a call from a tech that could help me understand how this system worked, and what could cause what I was seeing. That's all. Appears that may have been too much to expect.
I WILL update all on the outcome after the bulb swap. Thanks for listening.
-
Originally Posted by billybovine
If the hi/lo switch will not stay in position. That is a different problem and needs a different solution.
In addition, that switch has TWO "high" positions: Center is normal, low beam. Push one way for continuous high beam, push the other for momentary high beam (flash to pass). What he is seeing with the switch is likely normal.
-
Originally Posted by teninospyder
Need someone's help in understanding what is "possibly" happening here, and how to know for sure....then how to fix. Here is what I know
1. First noticed yesterday that when I started the Spyder, the right front headlamp appeared to be in "high beam" condition, with no light at all in the left light.
2. Tried the hi/lo switch, and the switch would not stay in the lo beam position but the shutter sound (which I actually had never heard before and didn't even know about) appeared, and the right light seemed to show both beams trying to be on for an instant.
3. Pulled both fuses and tried one at a time, but no light from either side unless both fuses were in.
That's where I am right now. I'm tending to lean towards a bad rocker switch on the dash, but............not sure how to check further.
Would 1 burned out bulb cause this ??? Doesn't seem so, but with this setup, who knows....
Your bike uses halogen bulbs, and they do burn out. So, replace that one first.
While you've got the tupperware off, remove the headlight assembly with the iffy shutter and pull off the back piece to expose the shutter and bulb. It's possible the shutter mechanism is being interfered with by one of the wires in there. Or, the shutter is bad (not likely if you're hearing the shutter mechanism but possible). With the headlight assembly removed and the back piece removed, you can hook up the wires and have someone hit the hi/lo switch while you watch what is going on.
2014 RTL Platinum
-
Active Member
Thanks to all for comments
Originally Posted by teninospyder
Need someone's help in understanding what is "possibly" happening here, and how to know for sure....then how to fix. Here is what I know :
1. First noticed yesterday that when I started the Spyder, the right front headlamp appeared to be in "high beam" condition, with no light at all in the left light.
2. Tried the hi/lo switch, and the switch would not stay in the lo beam position but the shutter sound (which I actually had never heard before and didn't even know about) appeared, and the right light seemed to show both beams trying to be on for an instant.
3. Pulled both fuses and tried one at a time, but no light from either side unless both fuses were in.
That's where I am right now. I'm tending to lean towards a bad rocker switch on the dash, but............not sure how to check further.
Would 1 burned out bulb cause this ??? Doesn't seem so, but with this setup, who knows....
From searching on this site for "headlight issues", I'm sure this isn't new to some of you. I have read about changing to LEDs and may do so while resolving this.
Any help appreciated.
Really appreciate all the input so far. anything others have or more that people think of, please add. Thanks again to all.
-
Active Member
Originally Posted by teninospyder
Really appreciate all the input so far. anything others have or more that people think of, please add. Thanks again to all.
Hello @teninospyder, We are so sorry to hear about your challenges. Please send us your VIN number and contact information to brp.care@brp.com and we will have a specialist reach out to you. Stephanie - BRPcare
-
Very Active Member
Originally Posted by teninospyder
Need someone's help in understanding what is "possibly" happening here, and how to know for sure....then how to fix. Here is what I know :
1. First noticed yesterday that when I started the Spyder, the right front headlamp appeared to be in "high beam" condition, with no light at all in the left light.
2. Tried the hi/lo switch, and the switch would not stay in the lo beam position but the shutter sound (which I actually had never heard before and didn't even know about) appeared, and the right light seemed to show both beams trying to be on for an instant.
3. Pulled both fuses and tried one at a time, but no light from either side unless both fuses were in.
That's where I am right now. I'm tending to lean towards a bad rocker switch on the dash, but............not sure how to check further.
Would 1 burned out bulb cause this ??? Doesn't seem so, but with this setup, who knows....
From searching on this site for "headlight issues", I'm sure this isn't new to some of you. I have read about changing to LEDs and may do so while resolving this.
Any help appreciated.
After all the discussion above and remembering how the headlights are wired, I'm inclined to think you have a broken wire or separated connector going to the left headlight and so the low beam relay, and thus the single filament bulb, is not being powered when you switch to high beam.
2014 Copper RTS
Tri-Axis bars, CB, BajaRon sway bar & shock adjusters, SpyderPop's Bumpskid, NBV peg brackets, LED headlights and modulator, Wolo trumpet air horns, trailer hitch, custom trailer harness, high mount turn signals, Custom Dynamics brake light, LED turn signal lights on mirrors, LED strip light for a dash light, garage door opener, LED lights in frunk, trunk, and saddlebags, RAM mounts and cradles for tablet (for GPS) and phone (for music), and Smooth Spyder belt tensioner.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|