-
Very Active Member
A Arm Bushings
It seems that I need new A Arm bushings on my 2013 RTL. The dealer wants over $450 to replace them, I look at it and wonder if I could do this one.
I am sure some of you have done it, any advice, positive or negative are welcomed. Are there any videos out there that you know of for this?
Joe
U.S. Army Viet Nam Era Vet
2013 Spyder RT-L, Black Currant
Trunk mount dual SS flag holder
TricLed foam hand grips (awesome)
Chromed Soaring Eagle License Holder
Utopia Deluxe driver backrest
LED fender lighting
Fast Flash LED brake light
Spyder Pops LED/skid plate
-
as long as you have access to a press it should be a piece of cake. I would also replace the ball joints while you have it apart, whether they are bad or not. bushings at cheap cycle parts are shown at $13.97 each, ball joints at $45.97 each.
Last edited by quasi; 09-18-2017 at 07:04 AM.
-
Very Active Member
Why would he need access to a press exactly?
The best substitute for brains & knowledge is....................silence.
-
Very Active Member
tight fit
hey freddy , I am not looking at the area where this bushing fits , but I have replaced A frame bushings before ( in a 1970 ford car ) and they are a super "TIGHT " fit to put back into the housing of the A arm assembly , when you pull the links apart ( when the bushings are bad ) they fall right out , and the new ones almost seem like they will be 1 1/2 sizes to big , which needs to be pressed in ---- or ---- using a super size " c " clamp heavy duty c- clamp will press one in if you are careful and have extra hands to help hold the A arm and the -c- clamp while some one with a cheater bar spins the clamp to press in the bushing ! most likely a bigger c clamp than this one , a deep throated c- clamp
-
Very Active Member
All of this, thus far is very helpful. I was not planning on the press, so thanks, also the idea of a super clamp is interesting. I figure if nothing else, there are small shops around, if I take the arms off, bring it to them they will press them in for a minimal charge.
Thanks for the pricing, that is sure a lot less than $450.00.
Has anyone done it as a DIY? Other the aforementioned challenges, is difficult is it to remove and reinstall the arms. I did it on a 1963 Ford Falcon about 100 years ago when I was young and stupid.
Joe
U.S. Army Viet Nam Era Vet
2013 Spyder RT-L, Black Currant
Trunk mount dual SS flag holder
TricLed foam hand grips (awesome)
Chromed Soaring Eagle License Holder
Utopia Deluxe driver backrest
LED fender lighting
Fast Flash LED brake light
Spyder Pops LED/skid plate
-
Very Active Member
I think our friend may nearly be able to do the job with little more than his bare hands, basic tools.and care.
Search should give results.
Last edited by Freddy; 09-19-2017 at 05:57 AM.
The best substitute for brains & knowledge is....................silence.
-
Very Active Member
Originally Posted by Freddy
I think our friend may nearly be able to do the job with little more than his bare hands, basic tools.and care.
Search should give results.
Yes, thanks, I tried to search the topic and could find nothing.
Though I visit here abou every day, and I glean much from the conversations, I find the search function totally uncooperative.
Joe
U.S. Army Viet Nam Era Vet
2013 Spyder RT-L, Black Currant
Trunk mount dual SS flag holder
TricLed foam hand grips (awesome)
Chromed Soaring Eagle License Holder
Utopia Deluxe driver backrest
LED fender lighting
Fast Flash LED brake light
Spyder Pops LED/skid plate
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|