https://www.lamonstergarage.com/belt-tensioner-idler-pulley/
I have an OEM tensioner with a Lamonster bearing...
Type: Posts; User: Rattlebars
https://www.lamonstergarage.com/belt-tensioner-idler-pulley/
I have an OEM tensioner with a Lamonster bearing...
as per mike's earlier recommendation I bought and installed Toyo Proxes T 185/55-15 and the nanny on my 2016 loves them as much as I do. No complaints from her at all. Ridden in all sorts of weather,...
Don't know if this will help.... might be pre D.E.S.S.
https://www.youtube.com/watch?v=a8xbXEE_ky4&t=729s
Once you get Two (2) keys (minimum) done put one under the service door hidden. You will save lots of money and grief. Get your son to pay for them and the new key unit and the programming and all....
by 2018, resetting the canbus by using the hazard lights to cure hyperflash went away. Not sure if this is true or not. Been asking for years for someone to confirm it's gone, but have not gotten a...
I made my own! So can you!
https://www.rattlebars.com/heated/
Separate part #.
193633
Another wise habit ... never get gas @ a station that has a tanker parked in it filling the underground cisterns. That stirs up all sorts of stuff into the fuel in the cisterns.
There are raised panels on each end. Insert finger from the front and lift. Get some plumbers grease and put on the pins to make it easier to do next time. Lifting from the rear of the panel will...
PC is not for me. All it does is change the throttle position sensor to "already on." Say to get the stock acceleration normally you twist the throttle from 0° for none to 90° for full acceleration. ...
Good choice. Both fine machines. My 16 has many features that the later models had eliminated. Older models many have better performance than newer.
Ultimate seat revived my ability to ride without back pain. Added my own backrest to it. Details at link in my signature.
193221
193222
I don't winterize. I have heated gear (make your own -> https://www.rattlebars.com/heated/) and find a way to ride all year 'round (much easier now since I have a winter home in SC :D ) If there is...
Start the bike which should resolve a low battery condition.
192896
192897
running these and love them (Thanx Mike). One must shim the fenders toward the bike using a pair of lock washers @ the bracket mounts. Complete details @ the link in my signature.
...
Sounds like a balance issue. Improper balance from the start or you may have thrown a wieght. I'm running Toyo Proxes T 185/55-15 up front and since the tire shop did not have "cones" small enough to...
From the fiche @ Partshark. If you do have the #350 one, double check the two mounting bolts #350a. The Loctite coating on them is so thick they take loads of torque to completely tighten down snug...
I have no problem using Rotella t6 5W40 and this time using Castrol 5w40 synthetic. Both purchased at Wally World for cheeep. Castrol seems to cause a bit of delay when starting out cold, but it...
From amazon. I've been using this as a broadcaster blue tooth to my headset from my old tv. My new tv has BT built in. I have switched this to receive and use it through the aux input on the F3. For...
What does that mean? If your idler is loose at the base where to the bolts are, it will eventually blow. Grab a ratchet and tighten the bolts. I believe they are 12mm.
Informative post with ONE EXCEPTION! The tires in the photos are NOT NAMED. Are we to accept "expert" testimony with such absence of vital information?
Bert. Please always give the year of your bike. They change most everything each year and consistency on solutions is patchy. Contact TricLED for a replacement of the side light. Sometimes they die....
By the wear pattern, it is "obvious" that the idler was left loose after your recent service. The idler was moving and dragged into the belt which melted the arm and destroyed the roller. I would...
There are many work arounds for those sources problems. You can set iTunes to do mp3 instead of ACC. You can get music off of many sources with "audacity". I wont' detail other ways, but there are...
I have an idler and replaced the roller with Lamonster's roller. Luv it. No vibes, nice ride.
https://www.lamonstergarage.com/can-am-spyder-f3-rt-belt-tensioner-idler-pulley-lamonster/
I installed a set of goldwing horns in the cavern under the frunk liner. Got them for less than $20 off eBay. Had great result with that. One must be aware that the OEM horn is switched by the ground...
@72 with agent orange and arthritis, I need LOTS of windshield. I have an f4 no vent 25" to which I added several things to accommodate my disabilities.
Visit the link in my signature to see...
Well, I'm in the 9000 mile group. Tire was showing cords (Kenda) and rear OEM pads were nearly gone, so much so that I had a heck of a time getting the rear piston started onto the threads!
I'm...
Cat pics!
190525
Think I got you beat. ;)Bought my air hawk at @Daytona Bike Week in 1997. Has served me well for 24 years. You are correct about inflation. Just a little bit. The actual trick to using them for long...