Search:

Type: Posts; User: mike3069

Page 1 of 17 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    24
    Views
    5,358

    Are you getting the steering angle and torque...

    Are you getting the steering angle and torque sensors reset at the same time as the alignment? Without resetting the sensors (with BUDS) after doing the alignment you can have the effects you guys...
  2. This comment is on the mark. I had the same...

    This comment is on the mark. I had the same experience with my '08 GS. After a lot of thought I concluded that the computer was making adjustments to the sensitivity to the yaw/body roll sensor when...
  3. Hi Mike. Try going to this link...

    Hi Mike. Try going to this link http://www.disabledmotorcyclerider.com and check out the kliktronic electric shifter system. This is what I use.
  4. Replies
    24
    Views
    3,398

    Go to www.mousesavers.com They have lots of...

    Go to www.mousesavers.com

    They have lots of info on any discounts that are available.
  5. No. The left handle bar button that you use to...

    No.

    The left handle bar button that you use to reset the scrolling screen display before you can start the spyder, is also a "mode" button. When you press it to reset the screen it also will...
  6. Replies
    324
    Views
    47,115

    '08 GS 40,000 miles

    '08 GS 40,000 miles
  7. Replies
    26
    Views
    8,803

    One thing you can do to check if it is the oil...

    One thing you can do to check if it is the oil sensor switch. Locate the switch on the lower right side of the motor and pull off the wire. The switch operates in a normally "open" position and...
  8. Replies
    19
    Views
    4,217

    No, I had to go with 175, but no mod required (it...

    No, I had to go with 175, but no mod required (it JUST fits)
  9. Replies
    19
    Views
    4,217

    In a word, YES! P.S.- I put on Faulkin...

    In a word, YES!

    P.S.- I put on Faulkin ZE912's, no mods needed. 20k miles and still going strong.
  10. Thread: ANTI-SWAY BAR

    by mike3069
    Replies
    36
    Views
    10,582

    When I installed Ron's sway bar on my RS, I...

    When I installed Ron's sway bar on my RS, I noticed the improvement in the handling on the FIRST corner. I went through the 90 degree corner at the light 1/4 mile from home and was instantly aware of...
  11. Replies
    26
    Views
    7,210

    Ron, that post just cost me 5 hours and I got my...

    Ron, that post just cost me 5 hours and I got my moneys worth out of that link!

    P.S. I LOVE my sway bar!
  12. Replies
    20
    Views
    3,349

    :agree: One of the "other parameters" adjusted...

    :agree:

    One of the "other parameters" adjusted is the sensitivity of the yaw sensor that controls the degrees of body roll allowed before the nanny kicks in when cornering, i.e. when the switch is...
  13. Replies
    18
    Views
    1,980

    Now THAT is a HORN!

    http://twentytwowords.com/2012/08/22/scooter-with-a-train-horn-pictures-and-video/
  14. Replies
    12
    Views
    2,707

    :agree:

    :agree:
  15. This thread is a great example of what can result...

    This thread is a great example of what can result from an instance of "misguided" customer service. All of the ranting and back and forth commenting could have been prevented by a better trained and...
  16. Replies
    2
    Views
    1,157

    Thanks Jesse! That's what I wanted to know.

    Thanks Jesse! That's what I wanted to know.
  17. Replies
    2
    Views
    1,157

    Rear shock replacement question

    I need a new rear shock. My question is what is the difference between the rear shock on the RS and the RS-S? The RS shocks are listed as not available until Aug. 15, but the RS-S shock is available...
  18. I don't see Ride-On on the sponsor page...

    I don't see Ride-On on the sponsor page anymore.:dontknow:

    I think the code was "Lamonster" if you want to try it.
  19. Replies
    8
    Views
    3,031

    The filter size was increased to allow for a...

    The filter size was increased to allow for a longer oil change interval.

    Old (short) filter = 3000 miles

    New (long) filter = 5000 miles
  20. Replies
    9
    Views
    2,842

    I have the "Missing air dam" and a home made...

    I have the "Missing air dam" and a home made deflector to send the heat out the hole in the side instead of on my foot. Also the underside panels have been removed. The panels came off @ 5k miles,...
  21. Replies
    9
    Views
    2,842

    On my last few rides I have noticed that the DPS...

    On my last few rides I have noticed that the DPS seems to not be working well. These have all been hot days. It seems that in a steady state higher speed turn the assist stops working. At first I...
  22. Replies
    7
    Views
    2,028

    NO! You are not missing a bolt. That is an empty...

    NO! You are not missing a bolt. That is an empty hole on my '08 GS also. nojoke
  23. Thread: July 7, 1980

    by mike3069
    Replies
    12
    Views
    3,334

    :thumbup: Happy Anniversary from one survivor to...

    :thumbup: Happy Anniversary from one survivor to another!
  24. Replies
    19
    Views
    4,213

    OK ... PM ME too!:roflblack:

    OK ... PM ME too!:roflblack:
  25. Replies
    2
    Views
    1,375

    Thanks for the "Like" button also!

    Thanks for the "Like" button also!
  26. Replies
    59
    Views
    23,154

    Over 30k miles on these floorboards and I STILL...

    Over 30k miles on these floorboards and I STILL think they are my best add-on mod.
  27. Replies
    14
    Views
    6,459

    As others have stated, it should be possible for...

    As others have stated, it should be possible for you to ride with one only arm. You may not need the semi-auto however. I have moved the clutch to the right side on my spyder due to nerve damage in...
  28. Replies
    213
    Views
    18,422

    Sorry, didn't see you in all that dust or I would...

    Sorry, didn't see you in all that dust or I would have stopped! :D
  29. I was in the vinyl business from 1985 to 1999,...

    I was in the vinyl business from 1985 to 1999, started with the very first dedicated vinyl cutter and ended with the latest (at that time) digital printing stuff.

    I AM IMPRESSED!!!!!!

    Pete has...
  30. What Scotty said!:thumbup:

    What Scotty said!:thumbup:
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4