The best and only way to disperse water in petrol is to put methylated spirits in the tank as the water will mix with meth's.
Type: Posts; User: Bruce B
The best and only way to disperse water in petrol is to put methylated spirits in the tank as the water will mix with meth's.
Sweat as glad to help, you cad go to this BRP site and look up all models for info,
...
For the 2021 it is in Operators Guide under Headlights on pages 128-130
Go to page 132 of your user MESSAGES IN MULTIFUNCTION GAUGE
BUDS is the software and interface that BRP use, you can buy an after market interface or try and acquire BRP one like l did as per the photo and you can buy a licence with the BUDS program online as...
Have you still got your lock fuel cap on or have got an aftermarket cap.
Composite belts do NOT squeak and they do not have rubber teeth.
The squeak did start back in 2008 that is correct and it was the rear brake pads but as the F3 series has different type of pad it...
Composite belts them selves do not squeak, check the right hand side belt tension adjusting washer if you can move it by hand it will give you a rattle or what you think is a squeak sound.
Just to put things straight there is no (shiny metal) or metal of any description in a Spyder composite manufactured belt see attached photos, and by the way this belt I cut through with a Stanley...
Info is in your operators guide under EQUIPMENT CustomerAccessory Circuit page 43
This is what I have done using a 5'x8' trailer view photo's, I use 2 x 1"x3" boards I on either side and the tyre's just touch them keeping the guards away from the sides, and I use S/S eye nuts on...
Go to this and feed #25 https://www.spyderlovers.com/forums/showthread.php?107052-New-Tank-bag-for-F3
It looks like you are looking through the screen if that is correct you should change the screen so you are looking over the top of it which is the correct way.
If you read the operators manual that you should have it says this:
Display Brightness
The brightness of the display is factory setup by default at the maximum level.
The brightness may be...
172574172575
This I have done on several spyders
Why don't you get someone to take a side photo off you sitting on it with your hands on the bars.
Read your manual all that info is in it.
Actually I am in New Zealand
Updated link
http://epc.brp.com/Index.aspx?lang=E&s1=10c6fa1e-e75c-4faa-99b7-4bc16493a7d5
Sorry but they all now have the 79 tooth rear drives, to check this is correct all you have to do is go to this web site.
...
Sorry but they all now have the 79 tooth rear drives, to check this is correct all you have to do is go to this web site.
...
Drill a small hole at the end of the crack and it will stop it from going any more.
Just to help you make it even look better SpyderF3.
168998 168999 169000
Yep Treva, its there to ride not site in its shed but the weather has been a bit of a hold up but summers is on its way :2thumbs: so hopefully less rain, I ride all year round here but don't leave...
I am using the Kumho Ecowing 175/50 R15 75H runing at 19-20 PSI and have done so far 49000 Kl on them and still Ks left on them and I'm not a slow rider and now on my 3rd rear since fitting...
It is 92 lb-ft plus or minus 4
You have to remove the battery but not the horn then remove the clamp that holds the hose that goes to the motor carefully without damage to hose or T then remove hose off T bingo :yes:, go and buy a...
Well all your missing is the 7mm hex (or allen key) because that's the correct size for them.
Got to the Mustang site https://www.mustangseats.com/Category/Seats
Have you tried this way, before you push and turn the key try this push the back of the seat down with one hand then with the other push and turn the key then while key is turned try lifting the back...