Mine lasted less that 500 miles the bearings went out of the roller. tried to by a roller fro Doc but he wouldn't sell one
Type: Posts; User: Dennis elliott
Mine lasted less that 500 miles the bearings went out of the roller. tried to by a roller fro Doc but he wouldn't sell one
Does any one know of a front sprocket guard to kind of keep rocks from getting under the belt 2014 rtl
I see these little mirrors attached to the windshield on some RTs anyone know who sells them. the mirrors on the RT are just to low
thx
I rode up in the mountains as I was coming home on the down grades I would get a brake failure. Once I was on level ground I cycled the key and it went away.
when I got home I checked the...
My warrant is up in july I just yesterday I paid 1050 for 3 more yrs
I put the same one on the frunk your right don't get to close. but most don't notice it like you do
There's a post some where about putting the 2 piece grip over the stock heated grip.
Not sure where I saw it but on this site. you cant remove the stock grip and keep heated
probably pull it ok but stopping it is another thing, does it have trailer brakes.
BRP says 400 lbs
I bought a little conveyor roller on ebay. Drilled out the BRP damper to 5/16 cut the plastic shaft that went into the original roller back to about 1/8 inch. a 5/16 washer on both sides seems to...
Another Brp Damper failure.
I didn't even get 300 miles before the vibration was back. not even a bearing just plastic on plastic. I cold smell it when I got in the garage
sure enough wobbled...
I installed mine . the only advise I have is on the alignment.
there is a screw that goes into one of the holes where the vent wing was put that screw in to hold the alignment then mark the other...
yes I'm was just curious. not really trying to reset anything
I have been a Goldwing rider for 20 yrs. still have one but I bought a 2014 rt limited.
My question is
if you start the Goldwing and don't touch the throttle let it run until the fans come on and...
I bought the Show Chrome isolated trailer wiring kit on EBAY every thing plugged in
I put a fuse block in and a relay power from battery ground to the gas tank bolt
I've heard there are problems with some vacuum lines
there are screws that come through the plastic in to the scoop.
Makes sure you mark the holes to be drilled then assemble the scoop and screw it on.
also make sure the front hole that goes in where...
Yes Doc Riverside sent me and email with the instrucions
Thanks Joe I checked it and save it. but they have nothing about the vents
Well my BRP vents came today. wow what a pile of plastic and no directions. This is going to be fun.
I found a couple metal strips I'm not sure about yet. Not sure what I expected LOL but that...
I have the midland handheld cb and Bluetooth I love it works great. Motorcycledave makes a cable to run the rt radio thru Bluetooth so I have everything
Thanks BlueKnight i had 30 psi ill lower it down today
I put on a new car tire 215 60 15 that part went smooth. when I went to put the caliper back on it wouldn't go, so I ended up taking the brake pads out and rotating the plunger back in.. of course...
Sounds to me like you have a front alignment problem. I would take it back nd ask them to check it. no way the tired should squeal over 20 an the steering be dirty like that
I bought the show chrome wiring harness. it was a very easy install. I did install a fuse block in the front under the panel and attached direct to the battery so as not to be connected to the...
I bought the show chrome wiring harness. it was a very easy install. I did install a fuse block in the front under the panel and attached direct to the battery so as not to be connected to the...
I'm sure the Brp Engineers put a lot of thought into the placement
Thanks guys I sent Dave an email I'm sure he will fix me up:yes:
I'm sure this has been asked before but I couldn't find it.
Is there anyway to hook the RT radio up to Bluetooth. Maybe a cable I can buy?
I have my phone and cb radio already on Bluetooth.
I...
I ordered the brp damper a couple weeks ago its been back ordered jan 13 they say
I just ordered the tensioner from brp still waiting got it. got the install kit from roadster renovations looks to be an easy install same as lamonster price was about 87 bucks