Search:

Type: Posts; User: Sweetwater

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    389

    FS: 2016 F3 SE6 parts

    Oil filter kit, rear fender assy, stock muffler, stock catalytic converter, 17” and 13.25” brake rods
    Free for pickup on Long Island.
    Msavino392@gmail.com
  2. Replies
    61
    Views
    16,556

    I resolved the resonator issue by welding the...

    I resolved the resonator issue by welding the smallest flowmaster muffler into the cat delete pipe. It is a baffled muffler and I got all my bottom end back. its the small muffler with one end...
  3. Thread: ECU Flash

    by Sweetwater
    Replies
    558
    Views
    238,570

    Cold air intake

    I see mention of cold air intakes.... I’ve been looking for one for my f3s. Any ideas of where to buy, or build my own?
  4. Replies
    5
    Views
    1,180

    Ok.. thank you

    Ok.. thank you
  5. Replies
    5
    Views
    1,180

    laser alighment

    Does anyone know if there will be anyone doing laser alignments at the Americade?
  6. Replies
    15
    Views
    4,238

    OK thank you..

    OK thank you..
  7. Replies
    15
    Views
    4,238

    How much lower is the pedal with the new kit?...

    How much lower is the pedal with the new kit? What does the other kit offer that the new one does not?
  8. Replies
    16
    Views
    4,787

    So....142# in the air or on the ground?

    So....142# in the air or on the ground?
  9. Replies
    29
    Views
    8,889

    Dennis: I am assuming those are trap speeds? What...

    Dennis: I am assuming those are trap speeds? What was the 1/4 mile time?
  10. Replies
    24
    Views
    4,962

    I just had the axle out this weekend and there...

    I just had the axle out this weekend and there was no hole...Kinda surprised me. I will try lube next time. I only had luck when I tightened it from the left side and just held the right nut...
  11. Replies
    24
    Views
    4,962

    As an addition to above: thoughts on drilling the...

    As an addition to above: thoughts on drilling the end of the axle for a cotter pin? That single jam nut gives me the creeps.
    2016 f3s
  12. Replies
    24
    Views
    4,962

    Axle adjusters

    Has anyone looked into fitting better adjusters into our frames? You’d think there has to be one that fits that pushes AND pulls without simply getting loose. Having to bang on the wheel, and tighten...
  13. Replies
    37
    Views
    5,708

    That’s beautiful! Can you tell me how you...

    That’s beautiful! Can you tell me how you darkened the windshield? I’ve been trying to do that myself..
  14. Replies
    4
    Views
    1,266

    Bob... There are three separate ramps. I figured...

    Bob... There are three separate ramps. I figured I would have to back it in because the spyder wheels cant pass the wheel well of the truck going in forward.
  15. Replies
    4
    Views
    1,266

    motorcycle ramp

    Has anyone here tried out the "EZ Rider Big Boy ramp"... it comes up to 12 feet long and is wide enough if you leave the sections separate. I'd love to be able to back up my f3 into my pickup truck...
  16. Replies
    27
    Views
    4,730

    Tire rack

    It seems the tire rack has
    Yokohama advan ao48
    kumho ecsta ast
    pirelli p-zero trofeo
    pirelli p-zero system in our 225/50/15 size.
  17. Replies
    540
    Views
    161,743

    Thank u! What do we think??

    Thank u! What do we think??
  18. I don’t think that’s in the cards. I was just...

    I don’t think that’s in the cards. I was just looking to step up one width or so when replacing, provided there is clearance.
  19. rear tire

    The rear tire is original with 12,000 miles on it. Still on a quest for a slightly wider car tire that'll fit.
  20. I’m mostly... oddly enough, feeling improved low...

    I’m mostly... oddly enough, feeling improved low end and throttle response. It pulls better everywhere, but not really past 105.... it still creeps up to 119 or so. But on the way there it pulls...
  21. Thank you so much... will do in the spring. So...

    Thank you so much... will do in the spring. So far... about 500 miles on the flash and I love it.
  22. Intersting

    I wish he said something, I woulda waited. I sent mine to Canada. How will we know it’s available? Do you know where in the US?
  23. Replies
    540
    Views
    161,743

    pully cover removed..

    Anyone here remember seeing a pic of lamonsters bike with the pulley cover removed? he painted the pulley to match the bike I think, but I cant find the pic. It looks like the cover is just left off....
  24. Replies
    1,099
    Views
    309,948

    Sticky: Jcthorne... how do you bypass? Mine is 2016 F3S...

    Jcthorne... how do you bypass? Mine is 2016 F3S SE6
  25. Oh boy....

    Will I need to send it back? What’ll the difference be??
  26. Model

    I have the f3s semi auto. Cat delete (with small muffler welded in) and voodoo exhaust
  27. Two weeks ago

    I had the reflash done 2 weeks ago. It’s not a rocket, but like I said... it’s a pretty impressive difference. So far.. no codes... but u have me worried!
  28. Flash is great!

    I had my 2016 f3s done by monster..... it was well worth it. More power everywhere but oddly I noticed it most in neutral! Just MUCH more crisp and quicker revving. I can hear the intake honking...
  29. Replies
    20
    Views
    2,993

    Quickest times?

    Out of curiosity... what’s the quickest time we’ve heard of for a spyder in the quarter?
  30. Thread: RLS Exhaust

    by Sweetwater
    Replies
    27
    Views
    5,395

    Muffler in delete pipe

    What I’m saying about the pipe is I bought a flow master 10 muffler with an offset intake... cut out a section of the delete pipe that the muffler fit in, and welded the delete pipe ends back onto...
Results 1 to 30 of 52
Page 1 of 2 1 2