In my case, the P0340 fault did not affect the engine rpm or 70 MPH speed while driving on the freeway. So I drove the spyder to the dealer and had it replaced. Third party extended warranty paid for...
Type: Posts; User: Trapdoor
In my case, the P0340 fault did not affect the engine rpm or 70 MPH speed while driving on the freeway. So I drove the spyder to the dealer and had it replaced. Third party extended warranty paid for...
P0562 - System Voltage Low. Steps you can do is to check for blown fuse, load test the battery, check voltage output of voltage regulator (13 - 14.7 volts), check connection on the voltage regulator,...
Had the same problem with my 2017 F3S-SE6 at 7,097 miles. Bike parked in the garage for one week waiting for my appointment with the dealer. Two days before my appointment, I took the bike for a run...
Android phone and Windows 10 users: My procedure is to import the picture into the computer. Then I make a copy of the picture in case I "oops". Next, I right click on the picture and select "edit",...
When this no-start problem happened to me during my 2-wheel riding days, it was always corrosion on the battery terminals and corrosion on the chassis ground point. Next time it happens, I plan to...
I use the X-Grip to hold my smartphone even though the side-to-side movement irritated me. So I found a product at Home Depot that would dampen the side-to-side movement - Velcro coin #90362, black,...
I measured the diameter of both sway bars. For the OEM version, it is 14mm; Baja Ron's is 16mm.
The Baja Ron instructions said to remove them. Once removed I had planned to clean them up and paint them, which I did. I agree with you on "lifting the spyder high enough". The two pics are my...
I found out what I did wrong after looking at the parts list - I missed removing one torx screw. This screw was hidden from view because it was not visible like the other three torx screws unless I...
Push pin removed and I was able to slide it aft and rotate it out of the way. Still not able to separate the deflector part from the shell part of the clam shell assembly.
I ran into a problem while installing the Baja Ron sway bar on my 2017 F3S. I removed the torx and phillips screws on the two "clam shell assemblies" but they won't come apart. Something else is...
Very cool lights! Where can I get one?
Same here. I usually refuel when the gas gauge indicates 1/4 full. I alternate between mid grade or premium, if I can remember what I put in the last time.
I just recently removed and reinstalled my rear fender. The first step is to remove the license plate to access the electrical plug cover. Disconnect the electrical plug and separate the cable from...
Please, I need to know what the torque specification is for the Allen bolts that secure the rear fender support. I have a 2017 F3S-SE that I took the rear fender apart for a wash, wax and paint job....
Which LEDGlow light kit are you trying to install? How many hookup wires are on the light kit and how many light strips? I'm assuming the light kit has three wires (one for ground, one for 12V pos,...
A very good suggestion. Another way BRP can fix this issue is to have their dealerships focus on servicing the Spyders yet allow them to sell Spyders based on demands.
Are you looking for the old version or the newer IPS version? I have the old version that I purchased in 07/2017 for my 2017 F3-S. I used it for about two weeks before I took them off the Spyder. PM...
Thanks SpyderAnn01 for the info on how to check for codes. I tried it and it displayed "No Active Fault Code" on my 2017 F3S.
I compared the installation instructions between the 412 kit and the 431 kit. The 431 kit includes a torque specification chart for bolts, no part number for the idler pulley only, and comes with two...
Did you determine if the right signal lamp socket was not getting +12 volts to it or the lamp socket wasn't grounded properly?
Battery connections may be tight but corrosion between the posts and clamps will create problems. And, speaking from my two-wheel experience, don't forget the negative cable connection to the Spyder...
I bought the AdMore SMT Light Bar (Small) for my 2017 F3S but was NOT able to use it. The light bar is a 6-wire connection setup that was NOT compatible with the F3S 3-wire setup. The F3S 3-wire...
I just installed an auxiliary taillight on my MBL F3 rack. Took me a while due to electrical and mounting issues that I had to resolve before the actual installation. The electrical issues I had were...
Yes! The rack I installed on my F3S is MBL Innovations' newly designed F3 Rack.
Chupaca, I apologize for not including the pics to illustrate the issue with attachments. The pixel size for the pic that's not right side up is 3024 x 4032; the pic that is right side up was resized...
My first try at attaching pictures to a new thread never turned right side up :gaah:. Drove me nuts for almost an hour trying to figure out how to solve this problem. Finally clicked on the question...
My F3S has the BRP detachable passenger backrest and the Shad saddlebags already installed on it. I wanted to add the new F3 luggage rack from MBL Innovations but the instructions did not apply to...
I'm planning on buying Lamonster's F3 Fender Light Kit after watching the video. The video didn't show how to remove the OEM reflectors which I believe to be step #1 of the installation. Would...
Oops! Meant to say license plate frame.:pray: