Pete, Both designs look great. I purchased a clear product from a company in San Antonio and then had to make my own template to do the same. Wish you had this product last year. I too agree with...
Type: Posts; User: Hitman5363
Pete, Both designs look great. I purchased a clear product from a company in San Antonio and then had to make my own template to do the same. Wish you had this product last year. I too agree with...
I got mine from TricLed and wired them under my seat. When running down the road they are markers but also blink for turn indicators. However, when I hit my brakes they go out and then back on when...
I installed the Baja Ron sway bar after I had 4,000 miles on my F3 and actually I was not impressed one bit. Doing it over again I would just replace the stock plastic dog bones on the ends of the...
Here is a link to what I put around my gas tank. It comes in several widths and or lengths. Extremely easy to install and they say it lasts 7 years:
http://www.xpel.com/shop/
Good luck
Just changed all three of my shocks out to Elka Stage Five's as my wife and I combined are 340 lbs and bottomed out the rear shock on simple bumps. The Stage Five's are pricey but well worth the...
Will be looking at all wiring today.....to make sure the resistors ground and the blinking modules ground are the same. Which I believe may not be the case.....because resistors grounds are tied...
Already did.
I installed LED's from TricLED on the rear fender of my 2015 F3S SE6 where the red side marker reflectors were. I also installed Blinker Modules under the passenger seat and ran the hot wires down...
John, my dealer had both....the one with USB posts and the one with a cigarette lighter which I bought as my tire compressor uses the cigarette lighter style power plug. I installed under the...
I ordered the Elka Stage 5 with Hydraulic for the front and the Stage 5 with Hydraulic for the rear with also the Pre Load Adjuster.....can't wait to have them installed. The rear was custom made...
Just my 2 cents but .......SmoothSpyder has a better look....no spring hanging off the side.............easy install and easy adjustment
Sorry, thought you were talking about the Fog Lights. Yes, the top of the bike needs to come off to get to the headlights. Note, when you remove the upper panel under the gauge assembly and...
Lamont does have a installation video on his fog lights....I believe it is on his Website....or maybe it was on YouTube....but there is on.
Just the top access panels and side panels need to come off. I installed TricLED....super easy installation!!!
I have the tallest F4 on my 2015 F3-S and love it......there is absolutely no drilling required to mount it to your F3
I have the OHT3 from The Ultimate Trailers that lowers and raises by air. I use two straps on the rear tire and ratchet them down from the sides of the trailer and to the rear of the wheel. I use...
Agreed......I had the same issue until I realized the sequence of tightening the bolts...........actually a great and heavy duty rack for its size.
I just changed mine after only putting 2,500 miles on the engine after the first initial 3,000 mile check up....and the dealer changed the oil and checked everything out ....why....cause I over...
Yep.....even states it in your manual.
I replaced my OEM bulbs with TricLed's. And no, you do not remove the three factory bolts. If I did not have the OEM Fog lights I would have gone with installing Lamonster Garages LED Fog Lights as...
I spray a Teflon spray on the rubber washer and then on a rag and wipe around the inside of the tank area. I do this about once a month and it has stopped the hard closing gas cap issues.
I bought a product called Xpel, they are out of San Antonio, TX. I installed mine on the sides so my legs did not rub and it can be installed anywhere and was fairly easy to put on.
I installed the Smooth Spyder Tensioner which is advertised on the forum. Super easy install....super easy to adjust and has totally eliminated the vibration....Period!!!
That thing scares me....notice it shaking.....
What brand is your lift....kind of looks like the one Sears sells.....????
JC,
I just installed LED's from TricLED on my headlights. I am curious as to how you got the wiring in the large rubber boot that goes over the rear of the headlight assembly....did you cut a hole...
Mike,
Are you using the large or small on your F3? My cannonball seat is 14.5 wide but the large is 14 inches long which would hang over the tank area......if I go with the small it is only 11 x 11...
Go to the LED Headlight bulbs and look at the option menu to the right....open it and that is where the LED Bulbs for the OEM Fog Lights are.
Sorry. I got new LED bulbs for the headlights, LED bulbs for the OEM fog lights, LED's for the amber and red reflectors for the front fenders, LED's for the red rear fender reflectors and blinker...
Normally I would not comment on a vendor. However, I am making an exception to my rule. This past Thursday, around 10:30am I order $900.00 worth of TricLED products and today Saturday at 12:15 pm I...