Search:

Bump

I have the Factory air box, all you would need to do is pay shipping on it and I will send it with the K&N air filter

I have a like new K&N filter for the Can-am spyder Part number CM9908. They sell for 52.99 New asking 40.00 shipped.

Waimart has Rotella T6 which is 5w-40 full synthetic and very reasonably priced. It also meets all the oil requirements also.

Anybody running the PCFC with the maps supplied by PC.
I decided to add JT’s cold air to the RSS which already had the Two Bother’s dual cans on the exhaust and saw that PC has a tune that is...

Jerry you don’t actually drill through the control arm you drill through the plastic piece that actually sits on the control arm. Where they mount Is just a spot on the plastic dress piece.

All right think I am going to go with these. They are plug and play with on/off switch. Reflector style housing.

https://www.customdynamics.com/cool-magic-billet-bullets-for-can-am-spyder

...

Long Island area right now, pretty busy area with a lot of pot holes and Deer at night.

Probably why the search showed nothing. Those lights are from Custom Dynamics, back when I joined the forum in 09, Custom Dynamics and ESI were pretty popular for lighting options, figured since the...

Not really the wrong question I listed two style of lights both that mount in similar locations one the cool Magic billet
comparable to 50 watt halogen bulbs with a 30 degree pattern,
Second Led...

I am in suffolk

I did search nothing really mentions which sets are brighter.

Any input would help. I am looking for a bright set of lights for night driving, anybody know which shine more light out between these two, the Cool Magic Bullets or the LED Day runners?? Any...

I think you always do better buying privately, you avoid the dealer mark-up and the salesman crap. JMHO

Well I don't know much about clearwater, but my Dad and several guys I worked with are down in Pine Ridge Estates in Citrus County and the area there is AWESOME. Not a lot of traffic very quiet all...

Riverhead Long Island, till next June then it is Florida for the Golden years

I decided I wanted a 2012 RS-S and started casually looking on and off about two years ago. Well I found one that in my mind was a really good deal. 2012 RS-S original owner 3949 miles with Two...

Bump

Hi,
I have two extra sets of 8mm Dyna high performance wires for the Can-am spyder. These are for the GS model. They Have Larger boots for the coil end but I can supply shorter boots if you would...

Looking for aftermarket spark plug wires.
Thanks

Okay following up with an update. Fuel tank is completely rusted inside and so is fuel pump. Fuel filter strainer turned into powder. Replacing both tank and pump assembly. Removal is a bit of a pain...

I have a 2008 spyder and I believe the fuel pump is bad on it. Have any of you guys removed the fuel pump? I'm not really sure how to really get to it to pull it out. Thanks

Remove and bench test the starter. Went through this with an Indian motorcycle I own. Turned out to be a bad armature in the starter causing an internal short. Bike would start to crank for a second...

Looking for one around 5000 miles or less. Located in NY but will consider traveling upwards of a 1000 miles or so. Not a big dealer fan so I figured I'd try here first.
Thanks

2012 also had fox shocks I believe. From doing some more research and info from Bob, I think I will try and find a 2012. The fewer electronics to cause issues the better.

Not much of a price difference, being used numbers are all over the place. Didn't realize there was a change in the engine though, thought that was the same.

Any reason to take one over the other if buying used? I know the dash cluster and front fender lights are different on the 2013. looking for thoughts on the matter. Thanks

I have that in my garage but mine is grey with Jardines and a power commander plus I pulled off my secondery throttle plates. Bike is a beast.

It can be done for a daily driver without issues. Only really boosting when into the throttle other then that it has a by-pass valve. I don't think water would be an issue unless maybe you slightly...

Okay got it. I would have thought they would have had a rubber style boot or smaller fitting piece for up there.:shocked: