is there any one in the kansas city aera that would help me install the ron bar on my 2013 rt,or would come to my house to help or do the install i would pay some one for either.thanks i do have the bar just need help.:thumbup:
Printable View
is there any one in the kansas city aera that would help me install the ron bar on my 2013 rt,or would come to my house to help or do the install i would pay some one for either.thanks i do have the bar just need help.:thumbup:
It's just a little farther than a nice afternoon ride for me or I'd be happy to give you a hand. I'm confident you'll get a reply from someone living out your way.
Wish you were close i'd help ya. When you get it on let us know your thoughts on improvement. I'm gathering info before my purchase of one for my 13 RT.
Haven't done one yet. Sent you a PM with a few ideas
I would come help but am back in West Virginia working for a spell. If you havent done it when we get back to KS, will help.
thanks to my brothers that would help and i might still need help after you get back to kansas my phone is 785-214-1657 or my emil is napper39@yahoo.com.any body else with any ideas let me know.thanks:thumbup:
still looking for help:yikes:
Another one that is to far. I have said it before,,, noone lives around me. Get up really early and head toward bama is all I can say. Wish you were closer.
the 2012 modeals i might be able to try but for some reason the 2013 s you need to raise somthing up much higher to get the bar out,and i dont even know what they are talking about to raise up,any way ill prouble need to have the cycle shop do it when i take it in for the 600 mile check.thanks to you all and i do wished i lived closer to you.:chat:
still help:yikes::thumbup:
You need to raise the front of the bike up about 2 feet to have room to remove the bar, according to the directions. Haven't done hers yet, waiting on the bar I ordered this morning.Quote:
Originally Posted by napper39
wondering if it would come out sideways if I took a front wheel off?
Per a message from BajaRon about the 2013 install:
"Most use a combination of jack stands and a jack. They jack up their Spyder as high as they can and put jack stands under the Spyder. Then let the jack down and put blocks on it to raise the Spyder further. Some have put the jack stands on blocks as well."
i got two real good jacks but they dont go that high,why why do they try to make it so hard to do:gaah:i went around some curves to day and theleft hand was good but the right ones was squrley hope the bar helps:pray: still looking for help:bowdown:
I used car ramps mine with additional 4 inches on each ramp using staggered 2x8 's (nail them together with stair step configuration. It was high enough for my '12....?
Sent from my iPod touch using Tapatalk
Even if you lived across the street I couldn't help you. I got my mechanic to install mine so I know it's right. I do know if you are adding a Bump Skid also install the Sway Bar first. :crackpipe:
The bump skid wont make a bit of difference. It is well in front of anything to do with the swaybar
Sent from my Galaxy S3. I may have made a spelling error or may have some grammer issues. My fingers are way to big to type on this tiny screen!
Did you get custom front fenders? Those look like 2012 fenders...Quote:
Originally Posted by napper39
JT
all the 2013 s bare bones rts come with those fenders,and come with blue or mag,coaler.:chat: still looking for help :thumbup:
I posted a video on the removal of the 2013 bar. It doesn't have the removal of the panels but it does show the actual removal and install of the bar.
https://www.youtube.com/watch?v=ej78...e_gdata_player
Sent from my Galaxy S3. I may have made a spelling error or may have some grammer issues. My fingers are way to big to type on this tiny screen!
You make it look so easy with the right tools.
With the right tools, you can do almost anything!Quote:
Originally Posted by scott16119